2006 Poulan P3314 P3314WS P3314WSA P3416 P3516PR P4018 P4018WM P4018WT P3818AV P4018AV P4018AV BH Chainsaw Owners Manual

KICKBACK SAFETY FEATURES
WARNING:
WE DO  NOT  REP-
WARNING:
The following features
RESENT  AND  YOU  SHOULD  NOT  AS-
SUME  THAT  THE  CHAIN   BRAKE  WILL
PROTECT YOU IN THE EVENT OF A KICK-
are included on your saw to help reduce the
hazard of kickback; however, such features
will not  totally eliminate this danger.   As  a
chainsaw user,donotrely  onlyonsafetyde-
BACK.
Kickback  is a  lightning  fast  action
which throws the bar and rotating chain back
and up toward the operator. Kickback can be
caused by allowing contact of the bar tip in the
danger zone with any hard object.   Kickback
can also be caused by pinching the saw chain
along the top of the guide bar. This actionmay
push the guide bar rapidly back toward theop-
erator.  Either of these events may cause you
to lose control of the saw which could result in
serious injury or even death. DO  NOT RELY
UPON ANY OF THE DEVICES BUILT INTO
YOUR SAW. YOU SHOULD USE THE SAW
PROPERLY AND  CAREFULLY  TO AVOID
KICKBACK.   Reduced--kickback guide  bars
and  low--kickback  saw  chains  reduce  the
chance and  magnitude of kickback  and are
recommended.  Your saw has a low kickback
chain and bar as original equipment. Repairs
on a chainbrake shouldbe madeby anautho-
rized servicing dealer.   Take your unit  to the
place of purchase if purchased from a servic-
ing dealer, or to the nearest authorized master
service dealer.
vices.
You must  follow all  safety precau-
tions, instructions, and maintenance in this
manual  to help  avoid kickback  and  other
forces which can result in serious injury.
S  Reduced--Kickback Guide Bar, designed
with a small radius tip which reduces the
size of the kickback  danger zone on the
bar tip.  A Reduced--Kickback Guide Bar
has been demonstrated to significantly re-
duce the number and seriousness of kick-
backs  when  tested in  accordance  with
safety requirements for gasoline powered
chain saws as set by ANSI B175.1.
Reduced Kickback  Symmetrical Guide Bar
Small Radius Tip
Symmetrical Guide Bar
S  Tipcontactinsomecasesmaycausealight-
ning fast reverse REACTION, kicking guide
bar up and back toward operator.
S  Pinching the saw chain along the top of the
guide bar  may push the  guide bar rapidly
back toward the operator.
S  Either of these reactions may cause you to
lose control of the saw which could result in
serious injury. Do not rely exclusively upon
devices built into your saw.
Large Radius Tip
S  Low--Kickback  Chain,  designed  with  a
contoured  depth  gauge and  guard  link
which  deflect kickback  force  and  allow
woodtogradually  rideintothecutter.Low--
Kickback  Chain has  met  kickback  per-
formance requirements when tested on a
representative sample of chain saws be-
low 3.8 cubic inch displacement specified
in ANSI B175.1.
WARNING:
Computed  kickback
angle(CKA) listedonyoursaw  andlistedinthe
CKA table below represents angle of kickback
your  bar and  chain  combinations  will have
when tested in accordance with CSA (Cana-
dian Standards Association)  and ANSI stan-
dards. When purchasing replacement bar and
chain, considerations  should be given to the
lower CKA values. Lower CKA values repre-
sent safer angles to the user, higher values in-
dicate more angle  and higher kick  energies.
Computed  angles represented  indicate total
energy andangleassociatedwithoutactivation
of the chain brake during kickback. Activated
anglerepresentschainstoppingtimerelativeto
activation angle of  chain break and resulting
kick angle of saw. In all cases lower CKA val-
ues represent a  safer operating environment
for the user.
Contoured
Depth Gauge
Elongated Guard Link
Deflects
kickback force
and allows wood
to gradually ride
into cutter
Low---Kickback
Chain
Can Obstruct Material
Not a Low---Kickback  Chain
S  Front Hand Guard, designed to reduce the
chanceofyour  lefthandcontactingthechain
if your hand slips off the front handlebar.
S  Position of front  and rear  handlebars, de-
signed with distance between handles  and
“in-line” witheach other. Thespread and“in-
line” position of the hands  provided by this
designwork together togivebalance  andre-
sistance in controlling the  pivot of the saw
back toward the operator if kickback occurs.
The following guide bar and chain combina-
tions meet  kickback requirements  of CSA
Standards  Z62.1,  Z62.3, &  ANSI  B175.1
when used  on saws  listed in this  manual.
Use of  bar  and chain  combinations other
than those listed  is not recommended and
may  not meet  the CKA  requirements  per
standard.
CHAIN BRAKE AND CKA ANGLE
S  Chain Brake, designedto stopthe chainin
the event of kickback.
5
Product Specification
CategoriesChainsaw Manuals, Poulan Chainsaw Manuals
Tags, , , , , , , , , ,
Model Year2006
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 19 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website