NOTE: Before felling cut is complete, use
wedges to open the cut when necessary to
controlthedirectionoffall. Toavoidkickback
and chain damage, use wood or plastic
wedges, but never steel or iron wedges.
S Be alert to signs that the tree is ready to fall:
cracking sounds, widening of the felling cut,
or movement in the upper branches.
Overcutting
Undercutting
Undercuttinginvolves cuttingon theunder-
sideofthelogwithtopofsaw againstthelog.
When undercutting use light upward pres-
sure. Hold saw firmly and maintain control.
The saw will tend to push back toward you.
S As tree starts to fall, stop saw, put it down,
and get away quickly on your planned re-
treat path.
S DO NOT cut down a partially fallen tree
withyour saw. Beextremely cautious with
partially fallen trees that may be poorly
supported. When a tree doesn’t fall com-
pletely,setthesawasideandpulldownthe
tree with a cable winch, block and tackle,
or tractor.
CUTTING A FALLEN TREE
(BUCKING)
Bucking is the term used for cutting a fallen
tree to the desired log size.
WARNING:
down to undercut. The saw cannot be con-
trolled in this position.
Always make your first cut on the compres-
sionsideofthelog. Thecompressionsideof
the log is where the pressure of the log’s
weight is concentrated.
Never turn saw upside
First cut on compression side of log
WARNING: Donot standon thelog
being cut. Any portion can roll causing loss
of footing and control. Do not stand downhill
of the log being cut.
IMPORTANT POINTS
S Cut only one log at a time.
S Cut shattered wood very carefully; sharp
piecesofwoodcouldbeflungtowardoper-
ator.
Second cut
Second cut
S Use a sawhorse to cut small logs. Never
allow another person to hold the log while
cuttingandnever holdthelogwith your leg
or foot.
S Do not cut in an area where logs, limbs,
and roots are tangled such as in a blown
down area. Drag the logs intoa clear area
before cutting by pulling out exposed and
cleared logs first.
First cut on compression side of log
BUCKING WITHOUT A
SUPPORT
S Overcut through 1/3 of the diameter of the
log.
S Roll the log over and finish with a second
overcut.
TYPES OF CUTTING USED FOR
BUCKING
S Watch for logs with a compression side to
prevent the saw from pinching. See il-
lustrations for cutting logs with acompres-
sion side.
WARNING:
If saw becomes
pinched or hung in a log, don’t try to force it
out. Youcanlosecontrolofthesawresulting
in injury and/or damage to the saw. Stop the
saw,driveawedgeofplastic orwoodintothe
cutuntil thesaw canbe removedeasily. Re-
startthesawandcarefullyreenterthecut. To
avoid kickback and chain damage, do not
useametalwedge. Donotattempt torestart
your saw when it is pinched or hung in a log.
BUCKING USING A LOG OR
SUPPORT STAND
S Remember your first cut is always on the
compression side of the log.
(Refer to the illustrations below for your
first and second cut)
S Your first cut should extend 1/3 of the
diameter of the log.
S Finish with your second cut.
Use a wedge to remove pinched saw
Using a log for support
2
nd Cut
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
Overcutting beginsonthetopsideofthelog
with the bottom of the saw against the log.
When overcutting use light downward pres-
sure.
1
st Cut
12
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro 220 LE, Poulan Pro 260 LE |
| Model Year | 2006 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)