Figure23
2.
Ensure that the distance between the pivot plate and the
wheel frame is 0 to 1/8 inch (0 to 3 mm) (Figure 24).
Figure22
1.
2.
Controlbarbracket
Springcover
3.
4.
Cableadjuster
Z-tting
2.
3.
Slide the spring cover up the cable adjuster. (Figure 22).
Unhook the Z-fitting from the cable adjuster, and
position it in a different hole on the adjuster to obtain a
gap of 1/8 to 1/4 inch (3 to 6 mm) between the control
bar bracket and the handle (Figure 22).
Note: Moving the Z-fitting to a hole closer to the
spring decreases the gap between the control bar
bracket and the handle; moving it to a hole farther from
the spring increases the gap.
Figure24
1.
2.
0to1/8inch(0to3mm)
Pivotplate
3.
Wheelframe
Important: If the pivot plate touches the wheel
frame before the control bar touches the handle,
the cable is too tight.
4.
5.
Install the spring cover over the cable adjuster.
Hook the spring end into the hole in the center of the
control bar bracket.
AdjustingtheTractionDriveCable
6.
Check the adjustment.
Note: After extended use, the drive belt may wear and lose
its proper belt tension. If the drive belt slips (continuously
squeals) under a heavy load, increase the belt tension by
inserting the spring end into the other hole in the control
bar bracket. The belt may slip in wet conditions; to dry out
the drive system, start the rotor and operate it without a
load for 30 seconds. Adjust the gap between the control bar
bracket and the handle to 1/8 to 1/4 inch (3 to 6 mm).
Unhook the Z-fitting from the pivot cable adjuster, and
insert it into a different hole to obtain the proper gap
between the pivot plate and the wheel frame (Figure 25).
AdjustingtheTractionDrive
Cable
Check the traction drive cable for proper adjustment initially,
after the first operating hour, and then annually thereafter.
CheckingtheTractionDriveCable
Figure25
1.
Squeeze the control bar against the right side of the
handle (Figure 23).
1.
2.
3.
Z-tting
Pivotcableadjuster
0to1/8inch(0to3mm)gap
4.
5.
Pivotplate
Wheelframe
11
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38602, Toro Snow Commander |
| Model Year | 2006 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Français |
| Serial Number | 260010001 - 260999999 |
| Product Name | Toro Snow Commander Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Single Stage Snow Commander |
| Swath | 24 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | 38602 |
| Engine Motor Model # | 084333-0199-E1 |
| Engine Motor Size | 141cc |
| Engine Motor Type | 2 Cycle EPA2 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)