MAINTENANCE
General
•
The L and H-jets are used to adjust the supply of fuel
to match the rate that air is admitted, which is
controlled with the throttle. If they are screwed
clockwise the air/fuel ratio becomes leaner (less fuel)
and if they are turned anti-clockwise the ratio
becomes richer (more fuel). A lean mixture gives a
higher engine speed and a rich mixture gives a lower
engine speed.
The user must only carry out the maintenance and
service work described in this manual.
IMPORTANT! Any maintenance other than that
described in this manual must be carried out by your
servicing dealer (retailer).
•
The T-screw regulates the throttle setting at idle
speed. If the T-screw is turned clockwise this gives a
higher idle speed; turning it anti-clockwise gives a
lower idle speed.
Carburettor adjustment
Due to existing environmental and emissions legislation
your chain saw is equipped with movement limiters on the
carburettor adjuster screws. These limit the adjustment
possibilities to a maximum of a 1/2 turn.
Basic settings and running in
The basic carburettor settings are adjusted during testing
at the factory. Avoid running at a too high speed for
extended periods during the first 10 hours.
H
L
CAUTION! If the chain rotates while idling theT-screw
must be turned anti-clockwise until the chain stops.
1/2
1/2
Rec. idle speed: 2700 rpm
Fine adjustment
When the machine has been ”run-in” the carburettor
should be finely adjusted.The fine adjustment should be
carried out by a qualified person. First adjust the L-jet,
then the idling screw T and then the H-jet.
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions.
Changing the type of fuel
Function
Fine tuning may be required if the chain saw, after
changing the type of fuel, performs differently with regard
to starting, acceleration, maximum speed, etc.
•
The carburettor governs the engine’s speed via the
throttle control. Air and fuel are mixed in the
carburettor.The air/fuel mixture is adjustable. Correct
adjustment is essential to get the best performance
from the machine.
Conditions
•
Before any adjustments are made the air filter should
be clean and the cylinder cover fitted. Adjusting the
carburettor while a dirty air filter is in use will result in
a leaner mixture next time the filter is cleaned. This
can give rise to serious engine damage.
•
The satisfactory operation of a catalytic converter
depends, among other factors, on the correct
adjustment of the carburettor. Carefully follow the
instructions below, using a tachometer as an aid.
•
•
•
Do not attempt to adjust the L and H jets beyond either
stop as this could cause damage.
•
•
Adjusting the carburettor means that the engine is
adapted to local operating conditions, e.g. climate,
altitude, petrol and the type of 2-stroke oil.
Now start the machine according to the starting
instructions and let it warm up for 10 minutes.
The carburettor has three adjustment controls:
L = Low speed jet
Place the machine on a flat surface so that the bar
points away from you and so that the bar and chain do
not come into contact with the surface or other
objects.
-
-
-
H = High speed jet
T = Idle adjustment screw
Low speed jet L
L
H
Turn the low speed jet L clockwise until it stops. If the
engine accelerates poorly or idles unevenly, turn the low
speed jet L anticlockwise until good acceleration and
idling are achieved.
T
English – 31
| Categories | Chainsaw Manuals, Husqvarna Chainsaw Manuals |
|---|---|
| Tags | Husqvarna 340, Husqvarna 340e, Husqvarna 345e, Husqvarna 350 |
| Model Year | 2007, 2008, 2009, 2010 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Product Brand | Husqvarna, Chainsaw |
| Document File Type | |
| Publisher | husqvarna.com |
| Wikipedia's Page | Husqvarna |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)