Poulan Pro PP10530ES 421064 Snow Blower Owners Manual

TO REMOVE WHEELS (See Fig. 24)
Remove the klik pin and remove wheel from axle.
NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and corrosion.
IMPORTANT: When installing  wheel, be sure  to use the
axle hole closest to the end  of the shaft – do not use the
hole in the wheel hub (if equipped). Inner hole in axle and
holeinwheelhubarenotusedforyourmodelsnowthrower.
ENGINE
See engine manual.
CARBURETOR
Your  carburetor is  not  adjustable.  Engine  performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine  does not operate properly due  to
suspected carburetor  problems, take your snow  thrower
to a qualified service center.
KLIK PIN (INSTALL
IN OUTER HOLE
OF AXLE ONLY)
OUTER HOLE
ENGINE SPEED
AXLE
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be  dangerous and will
void the warranty.  If you think  the engine-governed high
speed needs adjusting, contact a qualified service center,
which has proper equipment and experience to make any
necessary adjustments.
WHEEL
WHEEL HUB
FIG. 24
STORAGE
Immediately  prepare your  snow  thrower  for storage  at
the end of the season or if the unit will not be used for 30
days or more.
Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
Never use  engine or  carburetor cleaner products  in
the fuel tank or permanent damage may occur.
WARNING:   Never   store   the   snow
throwerwithgasolineinthetankinside
a building where fumes may  reach an
open flame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gasappliance. Allowtheenginetocool
before storing in any enclosure.
Use fresh fuel next season.
NOTE:  Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the  mix ratio found on stabilizer  container.
Run engine at  least 10 minutes after adding  stabilizer to
allow the stabilizer to reach the carburetor. Do not drain the
gas tank and carburetor if using fuel stabilizer.
SNOW THROWER
When snow thrower  is to be  stored for a  period of time,
clean it  thoroughly, remove  all dirt,  grease, leaves,  etc.
Store in a clean, dry area.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine
oil.  (See “ENGINE”  in  the  Maintenance section  of  this
manual).
1.
Clean entire  snow thrower (See “CLEANING”  in the
Maintenance section of this manual).
CYLINDER
2.
Inspect and replace belts, if necessary (See “TO RE-
PLACEBELTS”intheServiceandAdjustmentssection
of this manual).
Lubricate as shown in the Maintenance section of this
manual.
Besurethatallnuts,bolts,screws,andpinsaresecurely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
Touch up  all rusted or  chipped paint  surfaces; sand
lightly before painting.
1.   Remove spark plug.
2.
3.
4.
Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
Pullrecoilstarterhandleslowlyafewtimestodistribute
oil.
3.
4.
Replace with new spark plug.
OTHER
5.
Remove safety ignition key; store it in a safe place.
Do not store gasoline from one season to another.
Replace your gasoline  can if your  can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
ENGINE
See engine manual.
If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
Cover your  snow  thrower with  a suitable  protective
cover that does not retain moisture. Do not use plastic.
Plastic cannot breathe, which allows condensation to
form and will cause your snow thrower to rust.
FUEL SYSTEM
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuel hose,  or tank during  storage. Also, alcohol  blended
fuels (called  gasohol or  using ethanol or  methanol) can
attract moisture which leads  to separation and formation
of acids during  storage. Acidic gas can  damage the fuel
system of an engine while in storage.
IMPORTANT: Never cover snow thrower while engine/ex-
haust area is still warm.
18
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2008
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 40 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website