McCulloch M3816 M4218 Chainsaw Owners Manual

Overcutting beginsonthetopsideofthelog
with the saw against the log. When overcut-
ting use light downward pressure.
Undercutting
Using a support stand
2nd Cut
Overcutting
1
st Cut
st Cut
nd Cut
Undercuttinginvolves cuttingon theunder-
sideofthelogwithtopofsaw     againstthelog.
When undercutting  use light upward  pres-
sure.  Hold saw firmly and maintain control.
The saw will tend to push back toward you.
1
2
WARNING: Never  turn saw upside
down to undercut. The saw cannot be con-
trolled in this position.
First cut on pressure side of log
LIMBING AND PRUNING
WARNING:  Be alert  for  and  guard
against kickback.   Do  not allow  the moving
chain to contact any other branched or objects
at the nose of the guide bar  when limbing or
Second cut
Second cut
pruning.
Allowing such contact can  result in
serious injury.
WARNING: Never climb into a tree to
limb or prune.  Do not stand on ladders, plat-
forms,alog,or  inany positionwhichcancause
you to lose your balance or control of the saw.
IMPORTANT POINTS
S  Watch out  for springpoles.    Use extreme
caution when cutting small size limbs. Slen-
der materialmay catchthesawchainandbe
whipped toward you or pull you off balance.
S  Be  alert  for   springback.  Watch  out  for
branches that are  bent or under pressure.
Avoid being struck by the branch or the saw
when the tension  in the wood fibers  is re-
leased.
First cut on pressure side of log
BUCKING WITHOUT A
SUPPORT
S  Overcut through 1/3 of  the diameter of the
log.
S  Roll the log over and finish with a second
overcut.
S  Give special attention to logs under strain
to prevent the saw from  pinching.  Make
the first cut on the pressure side to relieve
the stress on the log.
BUCKING USING A LOG OR
S  Keep a  clear work  area. Frequently  clear
branches out  of the  way to  avoid tripping
over them.
LIMBING
SUPPORT STAND
S  Remember your first cut is always on the
pressure side of the log.
S  Your first  cut  should  extend  1/3  of the
diameter of the log.
S
Alwayslimbatreeafter  itis  cutdown. Only
then can limbing be done safely and prop-
erly.
Leave  the  larger limbs  underneath  the
felled tree to support the tree as you work.
S  Finish with your second cut.
Using a log for support
S
2
nd Cut
S  Start at base of the felled treeand work to-
ward the top, cutting branches and limbs.
Remove small limbs with one cut.
S  Keep the tree between you and the chain
as much as possible.
S  Remove larger, supporting branches with
thecuttingtechniquesdescribedinBUCK-
ING WITHOUT A SUPPORT.
S  Always use an  overcut to cut small  and
freely hanging limbs.  Undercutting could
cause limbs to fall and pinch saw.
1
st Cut
1
st Cut
PRUNING
WARNING:  Limit  pruning to  limbs
shoulder  height  or below.    Do  not  cut if
branches are higher than your shoulder.Get
a professional to do the job.
2
nd Cut
12
Product Specification
CategoriesChainsaw Manuals, McCulloch Chainsaw Manuals
Tags,
Model Year2009, 2010
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 17 pages
LanguageEnglish
Product BrandMcCulloch. Support Phone for US: Wheeled (Mowers, Tractors, Tillers, Snow Throwers) - 1-800-849-1297
McCulloch Handheld (Chainsaws, Trimmers, Blowers, Edgers) - 1-800-554-6723 All McCulloch Products - 1-800-521-8559, Chainsaw
Document File TypePDF
Publishermcculloch.com
Wikipedia's PageMcCulloch Motors
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website