Starting could require pulling the starter rope
handle many times depending on how badly
theunitis flooded. Ifengine fails to start,refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
OPERATING TIPS
S Check chain tension before first use, after
1 minute of operation, and each time be-
fore you start the chain saw. See CHAIN
TENSION in the ASSEMBLY section.
S Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary. If the chain
jumps off the guide bar, inspect the chain
for damageddrivelinks beforereinstalling.
Burrs on drive links, which prevent them
from entering the groove of the guide bar,
can be removed with a flat file.
CHAIN BRAKE
WARNING:
If the brake band is
worn too thin it may break when the chain
brakeistriggered.Withabrokenbrakeband,
the chain brake will not stop the chain. The
chainbrake shouldbe replacedby anautho-
rizedservicedealer ifany partis worntoless
than 0.020″ (0.5 mm) thick. Repairs on a
chain brake should be made by an autho-
rized service dealer. Take your unit to the
place of purchase if purchased from a ser-
vicing dealer, or to the nearest authorized
master service dealer.
S Keep the chain out of dirt and sand. Even a
smallamountofdirtwilldullachain,increase
the possibility of kickback, and require chain
sharpening or replacement.
S Practice cutting a few small logs using the
following techniques to get the“feel” ofus-
ing your saw before you begin a major
sawing operation.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
S The
inertia--activated chain brake is
S
S
S
S
Squeeze the throttle trigger and allow the
engine to reach full speed before cutting.
saw frame
activated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
S If the brake is already activated, it is
disengagedby pullingthefronthandguard
back toward the front handle as far as
possible.
Begin cutting with the
against the log.
Keep the engine at full speed the entire
time you are cutting.
Allowthechaintocutforyou.Exertonly
light downward pressure. If you force
thecut,damagetothebar,chain,oren-
gine can result.
S Whencuttingwiththesaw,thechainbrake
must be disengaged.
Disengaged
Engaged
S
Release the throttle trigger as soon as
the cut is completed, allowing the en-
gine to idle. If you run the saw at full
throttlewithoutacuttingload,unneces-
sary wear can occur to the chain, bar,
and engine. It is recommended that
the engine not be operated for lon-
ger than 30 seconds at full throttle.
Toavoidlosingcontrolwhencutiscom-
plete,donotputpressureonsaw atend
of cut.
Braking function control
S
CAUTION:
The chain brake must be
checked several times daily. The engine
mustberunningwhenperformingthisproce-
dure. This is theonly instancewhen thesaw
should be placed on the ground with the en-
gine running.
S Stop the engine before setting the saw
down after cutting.
TREE FELLING TECHNIQUES
WARNING:
Check for broken or
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.
dead branches which can fall while cutting
causing serious injury. Do not cut near build-
ings or electrical wires if you do not know the
direction of tree fall, nor cut at night since you
will not be ale to see well, nor during bad
weather such as rain, snow, or strong winds,
etc. If the tree makes contact with any utility
line, the utility company should be notified im-
mediately.
Inertia activating function control
S Carefullyplanyour sawingoperationinad-
vance.
S Clear the work area. You need a clear area
all around the tree so you can have secure
footing.
S The chain saw operator should keep on
the uphill side of the terrain as the tree is
likelytorollor slidedownhillafteritisfelled.
S Study the natural conditions that can cause
the tree to fall in a particular direction.
Natural conditions that can cause a tree to
fall in a particular direction include:
WARNING:
When performing the
following procedure, the engine must be
turned off.
Grip the rear handle with your right hand and
the front handle with your left hand. Hold the
chain saw approximately 14″ (35cm) abovea
stump or other wooden surface. Release your
grip on the front handle and use the weight of
thesaw toletthetipoftheguidebar fallforward
and contact the stump. Whenthe tipof thebar
hits the stump, the brake should activate.
11
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan BH, Poulan P3314, Poulan P3314WS, Poulan P3314WSA, Poulan P3416, Poulan P3516PR, Poulan P3818AV, Poulan P4018AV, Poulan P4018WM, Poulan P4018WT |
| Model Year | 2009 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)