Poulan Pro PP4620AV Chainsaw Owners Manual

manual. Avoid contact with the muffler. A hot
muffler can cause serious burns.
ON/STOP SWITCH
To stop  the engine  move the  ON/STOP
switch to the STOP position.
To start the engine hold the saw firmly on the
ground as illustrated. Make  sure the chain is
free to turn without contacting any object.
Use only 15”---18” of rope per pull.
Hold saw firmly while pulling starter rope.
Starter rope handle
CHOKE/FAST IDLE LEVER
Left hand
on front
handle
FULL
HALF  OFF
Right foot through rear handle
STARTING A WARM ENGINE
WARNING:  Donotattempttothrow
or drop--startthechainsaw.  Doingso willput
the operator at risk of serious  injury due to
loss of control of the chain saw.
1.
2.
MoveON/STOP switchtotheONposition.
Pull the  choke/fast  idle lever  out to  the
HALF CHOKE position.
3.
4.
Pull the starter rope quickly with your right
hand until the engine starts.
Squeeze and release the throttle trigger
to allow engine to return to idle speed.
IMPORTANTPOINTS TOREMEMBER
Whenpullingthestarterrope,donotusethefull
extentoftheropeas   this can causethe ropeto
break. Do not let starter rope snap back. Hold
the handle and let the rope rewind slowly.
For cold  weather starting,  start the unit  at
FULL CHOKE; allow the engine to warm up
before squeezing the throttle trigger.
DIFFICULT STARTING (or starting a
flooded engine)
The engine may be flooded if it has not started
after 10 pulls.
Floodedengines canbeclearedofexcessfuel
by following the  warm engine starting proce-
dure  listed  above.   Ensure  the  ON/STOP
switch is in the ON position.
NOTE: Do not cut material with the choke/
fast idle lever at the FULL CHOKE position.
HELPFUL TIP
If your engine still does not
start  after following  these
Startingcouldrequiremanypulls   dependingon
how badly unit is flooded. If engine still fails to
start, refer to  TROUBLESHOOTING TABLE
or call 1-800-554-6723.
instructions,
please   call
1--800--554--6723.
CHAIN BRAKE
STARTING A COLD ENGINE (orwarm
engine after running out of fuel):
WARNING:  Ifthebrakebandisworn
too thin it may break when the chain brake is
triggered. With a broken brake band, the chain
brake will not stop the chain. The chain brake
should be replaced by  an authorized service
dealer if any part is worn to less than 0.020
NOTE:
In the  following steps,  when the
choke/fast idle lever is pulled out to  the full
extent, the correct throttle setting for starting
is set automatically.
1.
2.
3.
Move ON/STOP switch to the ON posi-
(0.5
mm) thick.   Repairs  on  a chain  brake
tion.
shouldbemadeby  anauthorizedservicedeal-
er. Take your unit to  the place of purchase if
purchased from a  servicing dealer, or  to the
nearest authorized master service dealer.
S  This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
Pullthechoke/fastidlelever  outtothefull
extent (to the FULL CHOKE position).
Pull starter rope quickly  with your right
handamaximumof10times.    Then,pro-
ceed to the next step.
NOTE: If the engine sounds as if it is trying
to start before the 10th pull, stop pulling and
immediately proceed to the next step.
S
The
inertia--activated   chain   brake   is
activated if the front hand guard is pushed
forward,  either  manually   (by  hand)  or
automatically (by sudden movement).
4.
5.
6.
Push the choke/fast idle  lever in to the
HALF CHOKE position.
Pull the  starter rope  quickly  with your
right hand until the engine starts.
Allow theenginetorunfor  approximately
S  If  the  brake  is  already  activated,  it  is
disengagedby pullingthefronthandguard
back  toward the  front handle  as  far as
possible.
S  Whencuttingwiththesaw,thechainbrake
must be disengaged.
30
seconds. Then, squeeze and release
throttletrigger toallow engineto  returnto
idle speed.
10
Product Specification
CategoriesChainsaw Manuals, Poulan Pro Chainsaw Manuals
Tags
Model Year2009
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 20 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website