Poulan P3314 P3314WS P3314WSA P3416 P3516PR P4018 P4018WM P4018WT P3818AV P4018AV P4018AV BH Chainsaw Owners Manual

move the adjustment pin up and down the
screw. Locate this adjustment before you
begin mounting the bar onto the saw. See
following illustration.
Inside
view of
clutch
cover
Clutch
Cover
Adjusting Pin
Adjustment located on clutch cover
Lower
Hole
4.
Turn the adjusting screw by hand coun-
terclockwise until the adjusting pin  just
touches the stop. This should allow the
pin to be near the correct position.
Guide Bar
5.
Slide guide bar on bar bolts  until guide
bar stops against clutch drum sprocket.
12.
Install bar nuts  and finger tighten only.
Once the  chain is  tensioned,  you will
need to tighten bar nuts.
CHAIN TENSION
(Including units with chain already installed)
WARNING:  Wear protectivegloves
whenhandlingchain.  Thechainis  sharpand
can cut you even when it is not moving.
Bar bolts
NOTE:
When  adjusting  chain  tension,
make sure the bar nuts are finger tight only.
Attemptingto tensionthe chainwhen  thebar
nuts are tight can cause damage.
Guide bar
6.
Carefully remove the chainfrom thepack-
age. Hold  chain with  the drive  links as
shown.
Checking the tension:
Use the screwdriver end of the chain adjust-
ment tool  (bar tool) to  move chain around
guidebar.Ifthechaindoes   notrotate,itistoo
tight. Ifthechainis  tooloose,itwillsagbelow
the bar.
Tip of
Bar
Guide
Bar
CUTTERS MUST FACE IN
DIIRECTION OF ROTATION
Chain Adjustment
Cutters
Depth Gauge
Tool
Bar Nuts
Adjusting
Screw
(Bar Tool)
Adjusting the tension:
Chain  tension  is  very  important.  Chains
stretch during  use. This  is especially  true
during the first few times you use your saw.
Always check chain  tension each time be-
fore you start the chain saw.
Drive Links
7.
8.
Place chain over and behind clutch re-
tainer, fitting the drive links in the clutch
drum sprocket.
1.
Loosenbar nutsuntiltheyarefingertight
against the clutch cover.
Turn adjusting screw clockwise untilchain
solidly contacts bottom of guide bar rail.
Fit  bottom of  drive links  between  the
teeth in the sprocket in the nose of the
guide bar.
2.
9.
10.
Fit chain drive links into bar groove.
Pullguidebar  forward untilchain is snug
in guide  bar groove.   Ensure all  drive
links are in the bar groove.
Adjusting
Screw
11.
Now, install  clutch cover  making sure
theadjusting pinis positionedin  thelow-
er hole in the guide bar. Remember this
pin moves  the bar  forward and  back-
ward as the screw is turned.
7
Product Specification
CategoriesChainsaw Manuals, Poulan Chainsaw Manuals
Tags, , , , , , , , , ,
Model Year2010
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 21 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website