Poulan P4018WTL Chainsaw Owners Manual

Braking function control
The  chain  brake  must  be
checked  several times  daily.  The  engine
mustberunningwhenperformingthisproce-
dure. This is theonly instancewhen thesaw
should be placed on the ground with the en-
gine running.
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the  chain brake  by turning  your  left wrist
against  the hand  guard  without releasing
your grip around the front handle. The chain
should stop immediately.
the engine not be operated for lon-
ger than 30 seconds at full throttle.
S   To avoid losing control when cut is com-
plete, do not put pressure on saw at end
of cut.
CAUTION:
S
Stop the  engine  before setting  the saw
down after cutting.
TREE FELLING TECHNIQUES
WARNING: Check forbrokenordead
branches which can fall while cutting causing
seriousinjury.Donotcutnearbuildings    orelec-
trical wires if you do not know the direction of
treefall,nor  cutatnightsinceyouwillnotbeale
to see well, nor  during bad weather such as
rain, snow,  or strong winds,  etc.  If  the tree
makes contact  with any utility  line, the utility
company should be notified immediately.
S  Carefullyplanyour sawingoperationinad-
vance.
Inertia activating function control
WARNING:  When  performing  the
following  procedure,  the  engine must  be
turned off.
S  Cleartheworkarea.  Youneedacleararea
allaroundthetreeso   youcan havesecure
footing.
Grip therear handlewith your right handand
the front handle with your left hand. Holdthe
chainsaw approximately 14(35 cm) above
a stump or other wooden surface. Release
your grip  on the front  handle and  use the
weightofthesaw  toletthetipoftheguidebar
fallforwardandcontactthestump.   Whenthe
tipofthebar  hits thestump,the  brakeshould
activate.
S  The chain saw operator  should keep on
the uphill side of the terrain as the tree is
likelytorollor  slidedownhillafteritisfelled.
S  Study the natural conditions that can cause
the tree to fall in a particular direction.
Natural conditions that can cause a tree  to
fall in a particular direction include:
OPERATING TIPS
S  The wind direction and speed.
S  Check chain tension before first use, after
S  The lean of the tree.   The lean of  a tree
might not  be apparent due to  uneven or
slopingterrain.  Useaplumb or level tode-
termine the direction of tree lean.
1
minute of operation, and each time be-
fore you start the chain saw. See CHAIN
TENSION in the ASSEMBLY section.
S  Cut wood only.  Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S  Stop the saw if the chain strikes a foreign
object. Inspect the saw  and repair or re-
place  parts  as  necessary. If  the  chain
jumps off the guide bar, inspect the chain
for damageddrivelinks beforereinstalling.
Burrs on drive links,  which prevent them
from entering the groove of the guide bar,
can be removed with a flat file.
S  Weight and branches on one side.
S  Surrounding trees and obstacles.
Look for decay and rot. If thetrunk is rotted,
it can  snap and  fall toward  the
operator.
Check for broken  or dead branches which
can fall on you while cutting.
Make sure there is enough room for the treeto
fall. Maintain  a distance of  2-1/2 tree lengths
from the nearest person or other objects. En-
gine noise can drown out a warning call.
Remove dirt, stones, loose bark, nails, sta-
ples,andwirefromthetreewherecuts    areto
be made.
S  Keep the chain out of dirt and sand. Even a
smallamountofdirtwilldullachain,increase
the possibility of kickback, and require chain
sharpening or replacement.
S  Practice cutting a few small logs using the
following techniques to get the“feel” ofus-
ing your  saw before  you begin  a  major
sawing operation.
Plana clear retreat pathto therear anddiag-
onal to the line of fall.
Plan a clear retreat path
S
S
S
S
Squeeze the throttle trigger and allow the
engine to reach full speed before cutting.
saw  frame
Begin  cutting   with  the
against the log.
Direction of Fall
Keep the engine at full speed the entire
time you are cutting.
Allowthechaintocutforyou.Exertonly
light downward pressure.  If you force
thecut,damagetothebar,chain,oren-
gine can result.
45
_
FELLING LARGE TREES
(6 inches (15 cm) in diameter or larger)
The notch method is used to fell large trees.
A notchis cutonthesideofthetreeinthede-
sired direction  of fall.  After a felling  cut is
made on the opposite side of tree, the tree
will tend to fall into the notch.
S
Release the throttle trigger as soon as
the cut is completed,  allowing the en-
gine to idle.  If you  run the saw at full
throttlewithoutacuttingload,unneces-
sary wear can occur to the chain, bar,
and engine. It  is recommended that
11
Product Specification
CategoriesChainsaw Manuals, Poulan Chainsaw Manuals
Tags
Model Year2010
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 20 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Poulan P4018WTL Chainsaw Owners Manual 5.0 out of 5.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Poulan P4018WTL Chainsaw Owners Manual SKU UPC Model
Ned on Aug 30, 2016. 4018WT

Needed this for used chainsaw
Good to have the info on this saw


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website