Poulan P4018WTL Chainsaw Owners Manual

REPLACE SPARK PLUG
Tools required:
S  5/32 inch (4 mm) diameter round file and
file holder
The  spark plug  should  be replaced  each
year to ensure the engine starts easier and
runs better. Ignition timing is fixed and non-
adjustable.
S  Flat file
S  Depth gauge tool
NOTE:  This spark ignition system complies
TO SHARPEN CHAIN:
with the Canadian standard ICES--002.
1.
Move  ON/STOP switch  to  the STOP
position.
1.
2.
3.
4.
Loosen 3 screws on cylinder cover.
Remove the cylinder cover.
Pull off the spark plug boot.
Remove spark  plug from  cylinder and
discard.
2.
Check chain for proper tension.  Adjust
chain tension if necessary. See CHAIN
TENSION section.
3.
Sharpen cutters.
5.
Replace with Champion RCJ--7Y spark
To sharpen the cutters,  position the
file holder level (90˚) so that it rests
on the  top edges  of the cutter  and
depth gauge.
S
plug and tighten securely with a 3/ inch
4
(19
mm) socket wrench. Spark pluggap
should be 0.025 inch (0,6 mm).
Reinstall the spark plug boot.
the   cylinder  cover   and  3
screws. Tighten securely.
6.
7.
NOTE:  The chain has both left and
right hand cutters.
Reinstall
File Holder
Cutter
File
Cylinder
Cover
90˚
Depth Gauge
S
Align the 30˚ file holder marks paral-
lelwiththebar  andtothecenter  ofthe
chain.
Spark
Plug Boot
Cutter
Spark
Plug
30˚
File Holder Line
Cutter
S
Sharpen cutters  on  one side  of  the
chain first. File from the inside of each
cutter to  the outside.  Then,  turn the
chain saw around and repeat the pro-
cess for the other side of the chain.
Fileontheforward  strokeonly.  Use2
or 3 strokes per cutting edge.
Keep  all  cutters  the  same  length
when filing.
REPLACE FUEL FILTER
To replace fuel filter, drain your unit by run-
ning it dry of fuel.  Remove fuel cap and its
connected retainer from tank. Pull filter from
tank and remove from line. Replace and re-
assemble.
S
S
S
CHAIN ADJUSTMENT
SeeCHAIN TENSION in ASSEMBLY section.
File enough to remove any damage
to cutting edges (side plate  and top
plate of cutter).
CHAIN SHARPENING
WARNING: Improper chain sharpen-
ing techniques  and/or  depth  gauge mainte-
nance will  increase the  chance of  kickback
which can result in serious injury.
All Cutters
Same Length
Remove Damage
WARNING:  Wear  protective gloves
when handling chain. The chain is sharp and
can cut you even when it is not moving.
Conditions which indicate  the need for chain
sharpening:
Top Plate
Side Plate
S
File chain to meet the specifications
as shown.
S  Reduction in size of wood chips. The size
ofthewoodchipwilldecreaseas    thechain
gets duller  until it  becomes  more like  a
powder  than a  chip. Note  that  dead or
rotted wood will not produce a good chip.
S  Saw cuts to one side or at an angle.
S  Saw has to be forced through the cut.
80˚
60˚
30˚
16
Product Specification
CategoriesChainsaw Manuals, Poulan Chainsaw Manuals
Tags
Model Year2010
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 20 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Poulan P4018WTL Chainsaw Owners Manual 5.0 out of 5.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Poulan P4018WTL Chainsaw Owners Manual SKU UPC Model
Ned on Aug 30, 2016. 4018WT

Needed this for used chainsaw
Good to have the info on this saw


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website