S The
inertia--activated chain brake is
CHOKE/FAST IDLE LEVER
activated if the front hand guard is pushed
forward, either manually (by hand) or
automatically (by sudden movement).
S If the brake is already activated, it is
disengagedby pullingthefronthandguard
back toward the front handle as far as
possible.
FULL
HALF OFF
S Whencuttingwiththesaw,thechainbrake
must be disengaged.
Disengaged
STARTING A WARM ENGINE
Engaged
1.
2.
MoveON/STOP switchtotheONposition.
Pull the choke/fast idle lever out to the
HALF CHOKE position.
3.
4.
Pull the starter rope quickly with your right
hand until the engine starts.
Squeeze and release the throttle trigger
to allow engine to return to idle speed.
Braking function control
DIFFICULT STARTING (or starting a
flooded engine)
The engine may be flooded if it has not started
after 10 pulls.
Floodedengines canbe clearedof excess fuel
by following the warm engine starting proce-
dure listed above. Ensure the ON/STOP
switch is in the ON position.
Startingcouldrequiremanypulls dependingon
how badly unit is flooded. If engine still fails to
start, refer to TROUBLESHOOTING TABLE
or call 1-800-554-6723.
CAUTION:
The chain brake must be
checked several times daily. The engine must
be running when performing this procedure.
This is the only instance when the saw should
be placed on the ground with the engine run-
ning.
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the chain brake by turning your left wrist
against the hand guard without releasing
your grip around the front handle. The chain
should stop immediately.
CHAIN BRAKE
WARNING: Ifthebrakebandisworn
too thin it may break when the chain brake is
triggered. With a broken brake band, the chain
brake will not stop the chain. The chain brake
should be replaced by an authorized service
dealer if any part is worn to less than 0.020″
Inertia activating function control
WARNING:
When performing the
following procedure, the engine must be
turned off.
(0.5
mm) thick. Repairs on a chain brake
Grip the rear handle with your right hand and
the front handle with your left hand. Hold the
shouldbemadeby anauthorizedservicedeal-
er. Take your unit to the place of purchase if
purchased from a servicing dealer, or to the
nearest authorized master service dealer.
S This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
chain saw approximately 14″ (35 cm) above a
stump or other wooden surface. Release your
grip on the front handle and use the weight of
thesaw toletthetipoftheguidebar fallforward
and contact the stump. Whenthe tipof thebar
hits the stump, the brake should activate.
CUTTING METHODS
IMPORTANT POINTS
Keep the chain out of dirt and sand. Even a
smallamountofdirtwilldullachain,increase
the possibility of kickback, and require chain
sharpening or replacement.
S
S Check chain tension before first use, after
1
minute of operation, and each time be-
fore you start the chain saw. See CHAIN
TENSION in the ASSEMBLY section.
S Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary. If the chain
jumps off the guide bar, inspect the chain
for damageddrivelinks beforereinstalling.
Burrs on drive links, which prevent them
from entering the groove of the guide bar,
can be removed with a flat file.
S Practice cutting a few small logs using the
following techniques to get the“feel” ofus-
ing your saw before you begin a major
sawing operation.
S
S
S
S
Squeeze the throttle trigger and allow the
engine to reach full speed before cutting.
saw frame
Begin cutting with the
against the log.
Keep the engine at full speed the entire
time you are cutting.
Allowthechaintocutforyou.Exertonly
light downward pressure. If you force
thecut,damagetothebar,chain,oren-
gine can result.
11
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro PP4620AVX |
| Model Year | 2010 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)