Poulan Pro SM4218AVX Chainsaw Owners Manual

REPLACE FUEL FILTER
Fileontheforward  strokeonly.  Use2
or 3 strokes per cutting edge.
Keep  all  cutters  the  same  length
when filing.
S
S
S
To replace fuel filter, drain your unit by run-
ning it dry of fuel.  Remove fuel cap and its
connected retainer from tank. Pull filter from
tank and remove from line. Replace and re-
assemble.
File enough to remove any damage
to cutting edges (side plate  and top
plate of cutter).
CHAIN ADJUSTMENT
SeeCHAIN TENSION in ASSEMBLY section.
CHAIN SHARPENING
All Cutters
Same Length
Remove Damage
WARNING:
Improper chain sharp-
ening techniques and/or depth gauge mainte-
nance will  increase the  chance of  kickback
which can result in serious injury.
Top Plate
Side Plate
S
File chain to meet the specifications
as shown.
WARNING:
Wear protective gloves
when handling chain. The chain is sharp and
can cut you even when it is not moving.
Conditions which indicate  the need for chain
sharpening:
80˚
60˚
S  Reduction in size of wood chips. The size
ofthewoodchipwilldecreaseas    thechain
gets duller  until it  becomes  more like  a
powder  than a  chip. Note  that  dead or
rotted wood will not produce a good chip.
S  Saw cuts to one side or at an angle.
S  Saw has to be forced through the cut.
30˚
Hook Angle
0.025
(0.65
inch
mm)
Tools required:
S  5/32 inch (4 mm) diameter round file and
file holder
Rounded
Corner
Right
S  Flat file
S  Depth gauge tool
TO SHARPEN CHAIN:
Too Much Hook Angle
Squared Off
Corner
1.
Move  ON/STOP switch  to  the STOP
position.
2.
Check chain for proper tension.  Adjust
chain tension if necessary. See CHAIN
TENSION section.
3.
Sharpen cutters.
Wrong
S
To sharpen the cutters,  position the
file holder level (90˚) so that it rests
on the  top edges  of the cutter  and
depth gauge.
NOTE:  The chain has both left and
right hand cutters.
WARNING:
Maintain  the proper
hook angle  according to  the  manufacturer’s
specifications for the chain you are using. Im-
proper hook angle will increase the chance of
kickback which can result in serious injury.
File Holder
File
4.
Check and lower depth gauges.
Depth Gauge Tool
File
90˚
Cutter
Depth Gauge
Depth Gauge
S
Align the 30˚ file holder marks paral-
lelwiththebar  andtothecenter  ofthe
chain.
S
S
Place gauge tool on cutter.
Cutter
If the depth gauge  is higher than the
depthgaugetool,fileitleveltothetopof
the depth gauge tool.
S
Maintain  rounded   front  corner  of
depth gauge with a flat file.
NOTE:  The  very top of the  depth
gauge should  be flat  with the  front
half rounded off with a flat file.
3
0˚
Cutter
File Holder Line
S
Sharpen cutters  on  one side  of  the
chain first. File from the inside of each
cutter to  the outside.  Then,  turn the
chain saw around and repeat the pro-
cess for the other side of the chain.
If you require further assistance or are unsure
about performing this procedure, contact your
authorized service dealer or call our customer
assistance help line at 1--800--554--6723.
17
Product Specification
CategoriesChainsaw Manuals, Poulan Pro Chainsaw Manuals
Tags
Model Year2010
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 21 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website