Poulan Pro XT11530ES 429884 Snow Blower Owners Manual

OPERATION
TO START ENGINE
5.   Pull recoil  starter handle quickly. Do not allow starter
rope to snap back.
6.   Whentheenginestarts,releasetherecoilstarterhandle
and slowly move the choke control to the “OFF” posi-
tion.
Your snow thrower engine is equipped with both a 120 Volt
A.C. electric starter and a recoil starter. The electric starter
is equipped with a three-wire power cord and plug  and is
designed to operate on 120 Volt A.C. household current.
Be  sure  your house  is  a  120  Volt A.C.  three-wire
grounded  system.   If  you  are  uncertain,  consult a
licensed electrician.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operat-
ing temperature.
WARM START - RECOIL STARTER
WARNING:  Do  not   use  the  electric
starter if your  house is not a 120  Volt
A.C.three-wiregroundedsystem.  Seri-
ous personal injury or damage to your
snow thrower could result.
Follow the steps  above, keeping the choke in  the “OFF”
position.  DO NOT push the primer.
BEFORE STOPPING
Run the engine for a few minutes to help dry off any mois-
ture on the engine.
COLD START - ELECTRIC STARTER
IF RECOIL STARTER HAS FROZEN
If the recoil starter has frozen and will not turn the engine,
proceed as follows:
1.
Insert safety ignition key (tied to recoil start cord) into
ignition slot until it clicks. DO NOT turn the key. Keep
the extra safety ignition key in a safe place.
2.
3.
4.
5.
Place ON / OFF switch in “ON” position.
Rotate choke control to “FULL” position.
Connect the power cord to the engine.
Plug the other end of the power cord into a three-hole
grounded 120 Volt A.C. receptacle.
1.
Grasp the recoil starter handle and slowly pull as much
rope out of the starter as possible.
Release the recoil starter handle and let it snap back
against the starter.
2.
If the engine still  fails to start, repeat the  above steps or
use the electric starter.
NOTE: Do not  use primer when starting  engine with the
electric starter.
6.
SNOW THROWING TIPS
Push starter button until engine starts.
Go slower in deep, freezing  or heavy wet snow. Use
the drive speed control, NOT the ON / OFF switch, to
adjust speed.
It is easier and more efficient to remove snow imme-
diately after it falls.
The best time to remove snow is the early morning. At
this time the snow is usually dry and has not been ex-
posed to the direct sun and warming temperatures.
IMPORTANT: Do not crank engine more than five continu-
ous seconds between each time you try to start. Wait 5 to
10
7.
seconds between each attempt.
When the engine starts, release the starter button and
slowly move the choke control to the “OFF” position.
Disconnect the power  cord from the  receptacle first,
then from the engine.
8.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operat-
ing temperature.
Slightly overlap  each successive  path to  ensure all
snow will be removed.
Throw snow downwind whenever possible.
Adjust the skid plates to proper height for current snow
conditions.  See “TO ADJUST SKID PLATES” in this
section of this manual.
WARM START - ELECTRIC STARTER
Follow the steps above, keeping  the choke control in the
“OFF” position.
For extremely heavy snow, reduce the width of snow
removal  by overlapping  previous  path  and moving
slowly.
Keep engine clean and clear of snow during use. This
will help air flow and extend engine life.
Aftersnow-throwingiscompleted,allowenginetorunfor
a few minutes to melt snow and ice off the engine.
Clean the entire snow  thrower thoroughly after each
use and wipe dry so it is ready for next use.
COLD START - RECOIL STARTER
1.
Insert safety ignition key (tied to recoil start cord) into
ignition slot until it clicks. DO NOT turn the key. Keep
the extra safety ignition key in a safe place.
2.
3.
4.
Place ON / OFF switch in “ON” position.
Rotate choke control to “FULL” position.
Push the  primer four  (4) times if  the temperature  is
below 15°F, or two (2) times if temperature is between
15°
and 50°F. If temperature is above 50°F, priming is
not necessary.
WARNING:  Do not operate snow
thrower if weather conditions impair
visibility.  Throwing snow during a
heavy, windy snowstorm can blind
you and be hazardous to the safe
operation of the snow thrower.
NOTE:  Over priming may cause flooding, preventing the
engine from starting. If you do flood the engine, wait a few
minutes before attempting to start and DO NOT push the
primer.
13
Product Specification
CategoriesPoulan Pro Snow Blower Manuals, Snow Blower Manuals
Tags
Model Year2010
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 44 pages
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Snow Blower
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website