set the skids far enough down to prevent the auger
blades from contacting the ground.
2. Loosen or tighten the turnbuckle to adjust the pin
until it is the proper gap from the front edge of the
slot.
Note: The pivoting scraper on the snowthrower is
not recommended for use on gravel surfaces. But if
you must use the snowthrower on a gravel surface,
adjust the skids further down to prevent the pivoting
scraper from picking up rocks.
3.
Tighten the jam nut (Figure 46).
6.
Firmly tighten the nuts that secure both skids to the
auger sides.
Note: If the skids become excessively worn, you
can turn them over and set the unused side toward
the pavement.
Checking and Adjusting the
Traction Cable
Figure 46
1.
Jam nut
2. Turnbuckle
Service Interval: After the first 2 hours—Inspect
the traction cable and adjust it if
necessary.
Checking and Adjusting the
Auger/Impeller Cable
Yearly—Inspect the traction cable
and adjust or replace it if necessary.
Service Interval: After the first 2 hours—Inspect the
auger/impeller cable and adjust it if
necessary.
If the snowthrower does not drive in the forward or
reverse speeds or it drives when you release the traction
lever, adjust the traction cable.
Yearly—Inspect the auger/impeller
cable and adjust or replace it if
necessary.
With the traction lever disengaged, check the pin in the
elongated slot in the left side of the snowthrower above
the tire. There should be a gap of 1/32 to 1/16 inch (1
to 1.5 mm) from the front of the slot to the front edge
of the pin (Figure 45).
1.
2.
Remove the 2 screws from the right side of the belt
cover as shown.
Lift up the right side of the belt cover (Figure 47).
Figure 45
Figure 47
1.
2.
Pin
1/32 to 1/16 inch (1 to 1.5 mm)
3.
With the auger/impeller lever disengaged, ensure
that the gap between the auger clutch assembly and
the tab is 1/16 inch (1.5 mm) (Figure 48).
If the left hand (traction) cable is not properly adjusted,
do the following steps:
1.
Loosen the jam nut.
22
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38624, Toro 38634, Toro 38644, Toro 38654, Toro Power Max 1128OX |
| Model Number | 38624, 38634, 38644, 38654 |
| Model Year | 2010 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 310000001 - 310999999 |
| Product Name | Toro Power Max 1128 OXE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 28 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | 28 oz. (.83) 5w-30 or 10w-30 / API SH or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | 21M2140126E1 |
| Engine Motor Size | 342cc |
| Engine Motor Type | 4 Cycle CARB3, EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro Power Max 1128OXE 38624 38634 38644 38654 Snow Blower Operators Manual, 2010 5.0 out of 5.0 based on 1 product reviews. very good website very helpful