Inspecting the Rotor Blades
2.
Move the Z-fitting to a higher or lower hole on the
adjuster link as needed to obtain the 1/16-inch to
Service Interval: Yearly—Inspect the rotor blades and
have an Authorized Service Dealer
replace the rotor blades and scraper if
necessary.
1/8-inch
bar and the handle (Figure 22).
(2 mm to 3 mm) gap between the control
Note: Moving the Z-fitting higher decreases the
gap between the control bar and the handle; moving
it lower increases the gap.
Before each session, inspect the rotor blades for wear.
When a rotor blade edge has worn down to the wear
indicator hole, have an Authorized Service Dealer
replace the rotor blades and the scraper (Figure 24).
3.
4.
Hook the spring to the adjuster link and slide the
spring cover over the adjuster link.
Check the adjustment; refer to Checking the Control
Cable.
Note: After extended use, the drive belt may wear
and lose its proper belt tension. If the drive belt
slips (continuously squeals) under a heavy load,
disconnect the spring from the adjustor link and
move the upper end of the spring to the hole that
is further from the pivot point in the control bar
(Figure 23). Then connect the spring to the adjustor
link and adjust the control cable.
Figure 24
1.
Wear indicator hole
Servicing the Spark Plug
Service Interval: Yearly—Service the spark plug and
replace it if necessary.
Use a NGK BPMR4A spark plug or equivalent.
1.
2.
3.
Stop the engine and wait for all moving parts to stop.
Rotate the discharge chute so that it faces forward.
Remove the discharge chute; refer to the figure in
Installing the Discharge Chute procedure in the
Setup section.
Figure 23
4.
Remove the 4 screws that secure the shroud
(Figure 25).
1.
Upper end of spring
3.
4.
Pivot point
2.
Insert the upper end of
spring into this hole
Remove the upper end of
spring from this hole
Note: The belt may slip (squeal) in wet conditions;
to dry out the drive system, start the rotor and run
it without a load for 30 seconds.
12
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38587, Toro 38593 |
| Model Number | 38587, 38593 |
| Model Year | 2011 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 311000001 - 311999999 |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Power Clear, Snowthrower |
| Swath | 21 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | 0842330199E8 |
| Engine Motor Size | 141cc |
| Engine Motor Type | 2 Cycle EPA2 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 3 out of 3)
Lawn and Garden readers have rated Toro Power Clear 38587 38593 Snow Blower Operators Manual, 2011 3.0 out of 3.0 based on 1 product reviews. Not great, not the whole manual will not work for me