SERVICE AND MAINTENANCE
SHave PLaTe anD SKiD SHo eS
The shave plate and skid shoes on the bottom of the snow thrower are
subject to wear. They should be checked periodically and replaced
when necessary.
Skid Shoes
NOTE: The skid shoes on this machine have two wear edges. When
one side wears out, they can be rotated 180° to use the other edge.
1
.
.
Remove the six carriage bolts and hex nuts that secure the two
skid shoes to the sides of the auger housing. Refer to Figure 18.
Position the new skid shoes and secure with the carriage bolts
and hex nuts. Make certain the skid shoes are adjusted to be
level.
2
Shave Plate
1
.
Remove the hex nuts and carriage bolts that secure the shave
plate to the bottom of the housing.
Figure 18
2.
Remove the rear most hex nut and carriage bolt securing the back
of each skid shoe to the sides of the housing. Loosen the four
remaining hex nuts securing the skid shoes.
3
.
.
Slide the shave plate out of the off-set slot at the bottom of the
housing, and from between the skid shoes and side panels of the
housing.
4
With the mounting holes toward the back, slide the new shave
plate into position and secure with the fasteners removed
previously.
aDjUSTMenTS
Shift r od
If the full range of speeds (forward and reverse) cannot be achieved,
refer to the figure to the left and adjust the shift rod as follows:
1
.
Looking underneath the handle panel, note which of the three
holes in the shift lever the ferrule is inserted into. Also note the
direction of insertion. Then remove the internal cotter pin and flat
washer from the ferrule and withdraw the ferrule from the shift
lever. See Figure 19.
2
.
.
Place shift lever in sixth (6) position or fastest forward speed.
Push shift rod and shift arm assembly down sharply as far as it
will go to put the drive into the fastest forward position.
As necessary, rotate the ferrule up or down the shift rod until the
ferrule lines up with the hole from which it was earlier removed.
See Figure 19.
Figure 19
3
4.
5
.
.
From the direction noted earlier, insert the ferrule into the proper
hole.
6
Reinstall the washer and the internal cotter pin.
Chute Control
The distance snow is thrown can be adjusted by adjusting the angle of
the chute assembly. Refer to the Operation section for instructions.
The remote chute control cables have been pre-adjusted at the factory.
Move the remote chute lever on the control panel forward to pivot the
upper chute down; move the lever rearward to pivot the upper chute
up.
1
| Categories | Craftsman Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Craftsman 247.88033 |
| Model Number | 247.88033 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Español |
| Product Name | Craftsman 33-Inch Snow Thrower |
| Product Brand | Craftsman. Customer Service Representatives are available by phone: Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Swath | 33 inch |
| Engine Manufacturer | Craftsman |
| Engine Oil Type | SAE 5W30, 4-Cycle Engine Oil (Quart) Recommended for Temperature: - Above 32°F: SAE 30W Straight Grade; - 0°F to 32°F: SAE 5W-30 or SAE 10W-30 Multi Grade; - Below O°F: SAE 0W-30 Synthetic |
| Document File Type | |
| Publisher | craftsman.com |
| Wikipedia's Page | Craftsman (tools) |
| Copyright | Attribution Non-commercial |
(1 votes, average: 3 out of 3)
Lawn and Garden readers have rated Craftsman 247.88033 33-Inch Snow Blower Owners Manual 3.0 out of 3.0 based on 1 product reviews. craftsmen last forever... no issues with my other one.