TROUBLESHOOTING
War ning
Before performing any type of maintenance/service, disengage all
controls and stop the engine. Wait until all moving parts have come to
a complete stop. Disconnect spark plug wire and ground it against the
engine to prevent unintended starting. Always wear safety glasses during
operation or while performing any adjustments or repairs.
Thisat 1-800-4-MY-HOME®.section addresses minor service issues. To locate the nearest Sears Service Center or to schedule service, simply contact Sears
Problem
Engine fails to start
Cause
r emedy
1. Choke control not in ON position
1. Move choke control to ON position.
2
3
4
5
6
.
.
.
.
.
Spark plug wire disconnected
Faulty spark plug
2. Connect wire to spark plug.
3. Clean, adjust gap, or replace.
Fuel tank empty or stale fuel
Engine not primed.
4. Fill tank with clean, fresh gasoline.
5. Prime engine as instructed in the Operation Section.
6. Insert key fully into the switch.
Safety key not inserted.
Engine runs erratically
1. Engine running on CHOKE
1. Move choke control to OFF position.
2. Fill tank with clean, fresh gasoline.
3. Drain fuel tank. Refill with fresh fuel.
4. Contact your Sears Parts & Repair Center.
1. Contact your Sears Parts & Repair Center.
1. Stop engine immediately and disconnect spark plug
wire. Tighten all bolts and nuts. If vibration continues,
have unit serviced by a Sears Parts & Repair Center.
2.
3.
4.
Stale fuel
Water or dirt in fuel system
Carburetor out of adjustment
1. Carburetor not adjusted properly
1. Loose parts or damaged auger
Engine overheats
Excessive vibration
Loss of power
1. Spark plug wire loose.
Gas cap vent hole plugged.
1. Connect and tighten spark plug wire.
2. Remove ice and snow from gas cap. Be certain vent
hole is clear.
2.
Unit fails to propel itself
1. Drive cable in need of adjustment
Drive belt loose or damaged
1. Adjust drive control cable. Refer to Service and
Maintenance section.
2.
2. Replace drive belt. Refer to Service and Mainte-
nance section.
Unit fails to discharge snow
1. Chute assembly clogged.
1. Stop engine immediately and disconnect spark plug
wire. Clean chute assembly and inside of auger
housing with clean-out tool or a stick.
2. Stop engine immediately and disconnect spark plug
wire. Remove object from auger with clean-out tool
or a stick.
2.
Foreign object lodged in auger.
3.
4.
5.
Auger cable in need of adjustment.
Auger belt loose or damaged.
Shear pin(s) sheared.
3. Adjust auger control cable. Refer to Assembly
section.
4. Replace auger belt. Refer to Service and Mainte-
nance section.
5. Replace with new shear pin(s).
| Categories | Craftsman Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Craftsman 247.88033 |
| Model Number | 247.88033 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English, Español |
| Product Name | Craftsman 33-Inch Snow Thrower |
| Product Brand | Craftsman. Customer Service Representatives are available by phone: Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Swath | 33 inch |
| Engine Manufacturer | Craftsman |
| Engine Oil Type | SAE 5W30, 4-Cycle Engine Oil (Quart) Recommended for Temperature: - Above 32°F: SAE 30W Straight Grade; - 0°F to 32°F: SAE 5W-30 or SAE 10W-30 Multi Grade; - Below O°F: SAE 0W-30 Synthetic |
| Document File Type | |
| Publisher | craftsman.com |
| Wikipedia's Page | Craftsman (tools) |
| Copyright | Attribution Non-commercial |
(1 votes, average: 3 out of 3)
Lawn and Garden readers have rated Craftsman 247.88033 33-Inch Snow Blower Owners Manual 3.0 out of 3.0 based on 1 product reviews. craftsmen last forever... no issues with my other one.