MTD 190-032 101 42-Inch Two Stage Snow Blower Attachment Owners Manual

4
Assembly
& Attaching
Undercarriage
WARNING: Before installing  attachment, place tractor on a firm and level surface.  Place the
PTO in the disengaged (OFF)  position, set the parking brake, shut engine off  and remove key
to prevent unintended starting.
NOTE:operator’sReferencesposition. Referenceto LEFT andto theRIGHTFRONTindicateindicatesthe lefttheandgrillerightend;sidesto theof theREARtractorthewhendrawbarfacingend.forward in the
IMPORTANT:  You must first figure out which model of rider you are attaching this snow thrower to.  Refer to Determine
Your Model of Rider on page 3 of this manual to determine what model rider you are attempting to install this attachment
to.  Then proceed to the applicable instructions for your model of rider.
Your tractor’s cutting deck, PTO belt and front deck  stabilizer bracket must be removed prior to mounting the snow
thrower attachment. Refer to your tractor’s Operator’s Manual for detailed instructions.  If your tractor is equipped with
any front-end accessory (i.e. front bumper kit),  it must also be removed.
Do you have an Electric PTO or Manual PTO?
If you engage your tractor’s cutting deck by using your left  hand to pivot a lever forward, your tractor has a Manual
PTO. If you engage your tractor’s cutting deck by pulling outward  on a small knob located on the tractor’s dash, your
tractor has an Electric PTO.
Mounting the Idler Assembly
WARNING
Electric PTO Undercarriage
Assembly Setup
Proceed as follows when mounting this snow thrower
attachment to a tractor equipped with a 42, 46,  50 or
54-inch deck with electric  PTO:
Manual PTO Undercarriage
Assembly Setup
Before installing
attachment, place
tractor on a firm
1.  Install belt keeper pin as seen in Fig. 4-3.
2.
Attach the PTO cable to the idler bracket, then fit the
and level surface.
Place the PTO in
cable into the slotted fitting as seen in Fig. 4-3.
NOTE:  The PTO cable should be hanging down under
you tractor after you removed the mowing deck.  You will
need to slide the undercarriage unit under your tractor  in
position for which it will be mounted.  The slanted side
should be pointed towards the front of your tractor.
1.
Attach one end of the extension spring (732-0594A)
to the hole in the idler assembly. Mount the opposite
end of the extension spring to the belt keeper pin as
illustrated in Fig. 4-1.
the disengaged
(OFF) position, set
the parking brake,
shut engine off and
remove key to prevent
unintended starting.
2.
Refer to Fig. 4-2 for correct position.
2.
Refer to Fig. 4-4 for correct position.
Extension Spring
PTO Cable
Belt Keeper
Idler Pulley &
Idler Bracket
Idler Pulley &
Idler Bracket
Belt Keeper Pin
Flange Lock Nut
Figure 4-3
Slotted Fitting
Figure 4-1
Figure 4-2
Figure 4-4
10
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 24 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated MTD 190-032 101 42-Inch Two Stage Snow Blower Attachment Owners Manual 5.0 out of 5.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

MTD 190-032 101 42-Inch Two Stage Snow Blower Attachment Owners Manual SKU UPC Model
Andy Liviniuk on Dec 06, 2012. MTD 190-032-101 Snow Blower Manual

I was given an incomplete manual. I found this needmanual.com and was very happy to get exactly what I needed. It was simple to download and copy - no fuss no muss - thank you!


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website