MTD 600 Series C D Style Snow Blower Owners Manual

5
Operation
Starting The Engine
6.
When disconnecting the extension  cord, always unplug the
end at the three-prong wall  outlet before unplugging the
opposite end from the snow thrower.
1
.
Attach spark plug wire to spark plug.  Make certain the
metal loop on the end of the spark  plug wire (inside the
rubber boot) is fastened securely  over the metal tip on the
spark plug.
Recoil Starter
1
.
Rotate choke control to FULL choke position (cold engine
start).
2
3
.
.
Make certain both the auger control and  drive control are
in the disengaged (released) position.
NOTE: If the engine is already warm, place choke  control in
the OFF position instead of FULL.
Move throttle control up to FAST position. Insert  ignition
key into slot. Make sure it snaps into place. Do not attempt
to turn the key.
2
.
Push the primer two or three times for  cold engine start,
making sure to cover vent hole in the center of the primer
when pushing.
NOTE: The engine cannot start  unless the key is inserted
into ignition switch.
NOTE: DO NOT use primer to restart a warm  engine after a
short shutdown.
Electric Starter
NOTE: Additional priming may be necessary  if the
temperature is below 15° Fahrenheit.
Determine that your home’s wiring is a three-wire  grounded
system. Ask a licensed electrician  if you are not certain.
3
4
.
.
Grasp the recoil starter handle  and slowly pull the rope out.
At the point where it becomes slightly  harder to pull the
rope, slowly allow the rope to recoil.
WARNING! The optional electric  starter is
equipped with a grounded three-wire  power cord
and plug, and is designed to operate  on 120 volt AC
household current. It must be  used with a properly
grounded three-prong  receptacle at all times to
avoid the possibility of electric  shock. Follow all
instructions carefully  prior to operating the electric
starter.
Pull the starter handle with a firm,  rapid stroke. Do not
release the handle and allow it to snap back.  Keep a firm
hold on the starter handle  and allow it to slowly recoil.
5.
As the engine warms, slowly rotate the  choke control to the
OFF position. If the engine falters,  quickly rotate the choke
control back to the FULL position and then slowly  into the
OFF position again.
If you have a grounded three-prong  receptacle, proceed as
follows:
NOTE: Allow the engine to warm up for a few minutes after
starting. The engine  will not develop full power until it
reaches operating temperatures.
1
.
Plug the extension cord into the outlet located  on the
engine’s surface. Plug the other end of extension  cord
into a three-prong 120-volt, grounded,  AC outlet in a well-
ventilated area.
Stopping The Engine
2
.
Rotate choke control to FULL choke position (for a cold
engine start).
Run engine for a few minutes before stopping  to help dry off any
moisture on the engine.
NOTE: If the engine is already warm, place choke  control in
the OFF position instead of FULL.
1
2
3
.
.
.
Move throttle control to STOP position.
Remove the ignition key and store in a safe place.
3
4
.
.
Push the primer two or three times for  cold engine start,
making sure to cover vent hole in the center of the primer
when pushing.
Wipe all snow and moisture from the  area around the
engine as well as the area in and around the drive  control
and auger control. Also, engage and release  both controls
several times.
NOTE: Do NOT use primer to restart a warm  engine after a
short shutdown.
Push starter button to start  engine.
NOTE: Do NOT Do NOT hold the button down for longer
than seven (7) seconds at a time. Doing so may damage
your engine’s electric starter.
4
5
.
.
Once the engine starts,  release starter button.
As the engine warms, slowly rotate the  choke control to the
OFF position. If the engine falters,  quickly rotate the choke
control back to FULL and then slowly into the OFF position
again.
13
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 24 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website