6
.
While sitting in the operator’s position on the tractor, start
the engine and place the throttle lever in the FAST (rabbit)
position.
7
8
.
.
Move the tractor’s PTO (Blade Engage) into the ON position.
Remain in the operator’s position with the cutting deck
engaged for a minimum of two minutes, allowing the
underside of the cutting deck to thoroughly rinse.
9
1
1
1
.
Move the tractor’s PTO (Blade Engage) into the OFF
position.
0. Turn the ignition key to the STOP position to turn the
tractor’s engine off.
1. Turn the water off and detach the hose coupler from the
water port on your deck’s surface.
2. On 46” decks, repeat steps 4 through 11 on the opposite
side of the cutting deck.
IMPORTANT: After cleaning your deck with the Deck Wash
System™ , return to the operator’s position and engage the PTO.
Keep the cutting deck running for a minimum of two minutes,
allowing the underside of the cutting deck to thoroughly dry.
Figure 6-3
Side to Side
Adjustments
If the cutting deck appears to be mowing unevenly, a side to side
adjustment can be performed. Adjust if necessary as follows:
WARNING: Never attempt to make any
adjustments while the engine is running, except
where specified in the operator’s manual.
1
2
.
.
With the tractor parked on a firm, level surface, place the
deck lift lever in the top notch (highest position) and rotate
both blades so that they are perpendicular with the tractor.
Leveling the Deck
Measure the distance from the outside of the left blade
tip to the ground and the distance from the outside of the
right blade tip to the ground. Both measurements taken
should be equal. If they’re not, proceed to the next step.
NOTE: Check the tractor’s tire pressure before performing
any deck leveling adjustments. Refer to Tires on page 23 for
information regarding tire pressure.
3
.
Loosen, but do NOT remove, the hex cap screw on the left
deck hanger bracket. See Fig. 6-4.
Front To Rear
The front of the cutting deck is supported by a stabilizer bar that
can be adjusted to level the deck from front to rear. The front of
the deck should be between 1/4-inch and 3/8-inch lower than
the rear of the deck. Adjust if necessary as follows:
1
.
With the tractor parked on a firm, level surface, place the
deck lift lever in the top notch (highest position) and rotate
the blade nearest the discharge chute so that it is parallel
with the tractor.
2
.
Measure the distance from the front of the blade tip to
the ground and the rear of the blade tip to the ground.
The first measurement taken should be between 1/4” and
3/8”
less than the second measurement. Determine the
approximate distance necessary for proper adjustment and
proceed, if necessary, to the next step.
3
.
Locate the jam nut and lock nut on the front side of the
stabilizer bracket. See Fig. 6-3. After loosening the jam nut:
Tighten the lock nut to raise the front of the deck;
Loosen the lock nut to lower the front of the deck.
4
.
Retighten the jam nut loosened earlier when proper
adjustment is achieved.
Figure 6-4
4
.
Balance the deck by using a wrench to turn the adjustment
gear (found immediately behind the hex cap screw just
loosened) clockwise/up or counterclockwise/down.
The deck is properly balanced when both blade tip
measurements taken earlier are equal.
sectiOn 6— Maintenance & adjustMents
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals |
|---|---|
| Tags | MTD 610 Hydrostatic Tractor |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Product Type | Walk Behind Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)