IMPORTANT: Do not release the handle and allow it to
snap back. Keep a firm hold on the starter handle and
allow it to slowly recoil.
positions or two reverse (R) positions. Select a
speed appropriate for the snow conditions and a
pace you’re comfortable with.
•
As the engine warms, slowly rotate the choke
control to the OFF position. If the engine falters,
quickly rotate the choke control back to the FULL
position and then slowly into the OFF position
again.
IMPORTANT: Use the slower speeds until you are
comfortable and familiar with the operation of the snow
thrower.
•
Squeeze the auger control against the handle and
the augers will turn. Release it and the augers will
stop.
Stopping The Engine
•
•
Squeeze the drive control against the handle the
snow thrower will move. Release it and drive
motion will stop.
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
To help prevent possible starter freeze-up, proceed
as follows:
•
IMPORTANT: NEVER reposition the shift lever (change
speeds or direction of travel) without first releasing the
drive control and bringing the snow thrower to a
complete stop. Doing so will result in premature wear to
the snow thrower’s drive system.
Electric Starter (on models so equipped)
1.
Connect extension cord to the electric starter outlet
on the engine, then to 120 volt AC outlet.
With the engine running, push the starter button
and allow the starter for spin for several seconds.
The noise made by the starter is normal. The
engine’s starter is not being harmed.
When disconnecting the extension cord, always
unplug the end at the three-prong wall outlet before
unplugging the opposite end from the snow
thrower.
Move throttle control to STOP position.
Remove the ignition key (Do not turn key) to
prevent unauthorized use of equipment.
Wipe all snow and moisture from the carburetor
cover in the area of the drive control and auger
control. Also, engage and release the controls
several times.
2.
To Engage Augers
•
To engage the augers and start throwing snow,
squeeze the auger control against the left handle.
Release to stop the augers.
3.
NOTE: This same lever also locks auger control so
you can turn the chute directional control without
interrupting the snow throwing process.
4.
5.
•
Release the auger control; the interlock mechanism
should keep the auger control engaged until the
drive control is released.
6.
•
Release the drive control to stop both the augers
and the wheel drive. To stop the auger, both levers
must be released.
NOTE: Keep the key in a safe place. The engine
cannot start without the ignition key.
Auger Control Test
IMPORTANT: Perform the following test before
operating your snow thrower for the first time and at the
start of each winter season.
Recoil Starter
1.
With engine running, pull starter rope with a rapid,
continuous full arm stroke three or four times.
Pulling the starter rope will produce a loud
clattering sound, which is not harmful to engine.
Move throttle control to STOP position.
Remove the ignition key (Do not turn key) to
prevent unauthorized use of equipment.
Check the adjustment of the auger control as follows:
•
When the auger control is released and in the
disengaged “up” position, the cable should have
very little slack. It should NOT be tight.
2.
3.
•
In a well-ventilated area, start the snow thrower
engine as instructed earlier in this section under the
heading Starting the Engine. Make sure the throttle is
set in the FAST position.
NOTE: Keep the key in a safe place. The engine
cannot start without the ignition key.
•
•
While standing in the operator’s position (behind
the snow thrower), engage the auger.
Allow the auger to remain engaged for
approximately ten (10) seconds before releasing
the auger control. Repeat this several times.
With the throttle control in the FAST (rabbit)
position and the auger control in the disengaged
“up” position, walk to the front of the machine.
4.
Wipe all snow and moisture from the carburetor
cover in the area of the drive control and auger
control. Also, engage and release the controls
several times.
•
To Engage Drive
•
With the throttle control in the Fast (rabbit) position,
move shift lever into one of the six forward (F)
11
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)