6
Maintaining
Your Lawn
Tractor
Deck Wash System™ (If equipped)
Your tractor’s deck may be equipped with a water port on
its surface as part of its deck wash system. Use the Deck
Wash System™ (sold separately) to rinse grass clippings
from the deck’s underside and prevent the buildup of cor-
rosive chemicals. Complete the following steps AFTER
EACH MOWING:
1
. Drive the tractor to a level, clear spot on your lawn,
near enough to a water sillcock (spigot) for your
garden hose to reach.
IMPORTANT: Make certain the tractor’s discharge chute
is directed AWAY from your house, garage, parked cars,
etc.
2.
Disengage the PTO (Blade Engage), move the shift lever
into the neutral position, set the parking brake, and stop the
engine.
3. Thread the hose coupler (packaged with your tractor’s
Figure 6-
Operator’s Manual) onto the end of your garden hose.
4.
Attach the hose coupler to the water port on your decks
surface. See Figure 6-3.
WARNING
5.
6.
Turn the water on.
While sitting in the operator’s position on the tractor, re-start
the engine and place the throttle lever in the FAST (rabbit)
position.
Never exceed the
maximum inflation
pressure shown on
the sidewall of the
tire.
7.
8.
9.
Disengage the parking brake.
Move the tractor’s PTO (Blade Engage) into the ON position.
Remain in the operator’s position with the cutting deck
engaged for a minimum of two minutes, allowing the
underside of the cutting deck to thoroughly rinse.
Batteries give off an
explosive gas while
charging. Charge
battery in a well
10.
11.
12.
13.
Moveposition.the tractor’s PTO (Blade Engage) into the OFF
Turnenginetheoffignitionand engagekey to thetheSTOPparkingpositionbrake. to turn the tractor’s
Turnwatertheportwateron youroff anddecksdetachsurface.the hose coupler from the
Repeat steps 4-11 on the opposite side of the cutting deck.
ventilated area and
keep away from an
open flame or pilot
light as on a water
heater, space heater,
furnace, clothes
Figure 6-3
Cutting Deck Removal
dryer or other gas
appliances.
NOTE: Models equipped with a 38-inch deck have one
deck idler pulley. Models equipped with a 42-inch deck
have two deck idler pulleys.
Always use a fuse
with the same amper-
age capacity for
replacement.
To remove the cutting deck, proceed as follows:
1.
2.
3.
Place the PTO (Blade Engage) lever in the disen-
gaged (OFF) position and engage the parking brake.
Lower the deck by moving the deck lift lever into the
bottom notch on the right fender.
Remove the belt from around the tractor’s engine
pulley and idler pulley(s). Refer to Changing the Deck
Belt on page 26 for detailed instructions.
Looking at the cutting deck from the left side of the
tractor, locate the hair pin clip that secures the deck
support rod on the rear left side of the deck. See
Figure 6-4.
4.
Figure 6-4
1
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals |
|---|---|
| Tags | MTD 760, MTD 779 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Product Type | Walk Behind Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated MTD Pro 760 779 Series Transmatic Lawn Tractor Lawn Mower Owners Manual 4.0 out of 4.0 based on 1 product reviews. I9 NEED KNOW WHAT YEAR MY LAWNS MTD PRO 760-779