•
•
Start the disabled tractor following the normal starting
instructions previously provided; then disconnect
the jumper cables in the exact reverse order of their
connection.
Control Lever Moved
Inward and in Neutral
Have the tractor’s electrical system checked and
repaired as soon as possible to eliminate the need for
jump starting.
Stopping the Engine
•
•
Place the PTO switch in the “OFF” position.
Move the RH and LH drive control levers fully outward
in the neutral position.
Figure 5-2
•
•
Engage the parking brake.
•
Move the throttle control lever forward to the full
throttle position (3500-3600 RPM). NOTE: Although the
tractor’s engine is designed to run at full throttle, when
performing a practice session the tractor must be operated
at less than full throttle (approximately 2500-3000 RPM).
This only applies to practice.
Move the throttle control between the half and full
throttle positions, and turn the ignition key to the “OFF”
position.
•
Remove the key from the ignition switch.
NOTE: Always remove the key from the ignition switch
to prevent accidental starting or battery discharge if the
equipment is left unattended.
WARNING!: Always maintain a firm grip on
the control levers. DO NOT release the control
levers to slow or stop the tractor; move levers
to neutral position using your hands.
Practice Operation (Initial Use)
Operating a zero-turn tractor is not like operating a
conventional type riding tractor. Although and because a
zero turn tractor is more maneuverable, getting used to
operating the control levers takes some practice.
•
To drive the tractor, firmly grasp the respective drive
control levers with your right and left hands and
proceed as instructed in the following sub section.
Driving the Tractor Forward
WARNING!: Keep all movement of the drive
We strongly recommend that you locate a reasonably
large, level and open “practice area” where there are no
obstructions, pedestrians, or animals. You should practice
operating the tractor for a minimum of 30 minutes.
control levers slow and smooth. Abrupt
movement of the control levers can affect the
stability of the tractor and could cause the
tractor to flip over, which may result in serious
injury or death to the operator.
Carefully move (or have moved) the tractor to the practice
area. When performing the practice session, the PTO
should not be engaged. While practicing, operate the
tractor at approximately 1/2-3/4 throttle and at less than
full speed in both forward and reverse.
•
Slowly and evenly move both drive control levers
forward. The tractor will start to move forward. See
Figure 5-3.
Carefully practice maneuvering the tractor using the
instructions in the following section “Driving the Tractor.”
Practice until you are confident that you can safely operate
the tractor.
DRIVINGFORWARD
Faster
Driving the Tractor
Slower
WARNING!: Avoid sudden starts, excessive
speed and sudden stops.
•
Adjust the operator’s seat to the most comfortable
position that allows you to operate the controls. See
seat adjustment in the ADJUSTMENTS section.
Neutral
Position
•
•
Release the parking brake.
Figure 5-3
Move the RH and LH drive control levers inward in the
neutral position. Refer to Figure 5-2.
•
•
As the control levers are pushed farther forward the
speed of the tractor will increase.
NOTE: If the control levers are not even in the neutral position,
refer to Maintenance & Adjustments for instructions to
adjust the levers so that they are even.
To slow the tractor move the controls lever rearward
to attain the desired speed, or move the levers to the
neutral position to stop the tractor.
sectiOn 5 — OperatiOn
15
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals |
|---|---|
| Tags | MTD RZT, Troy-Bilt RZT |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)