MAINTENANCE AND REPAIR INSTRUCTIONS
MAINTENANCE SCHEDULE
NOTE: Maintenance, replacement, or repair of the emission
control devices and system may be performed by a
Troy-Bilt or other qualified service dealer. Call 1-800-
520-5520 for more information.
Perform these required maintenance procedures at the
frequency stated in the table. These procedures should also be
a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require special
tools or skills. If you are unsure about these procedures,
take your unit to a Troy-Bilt or other qualified service
dealer. Call 1-800-520-5520 for more information.
WARNING: To prevent serious injury, never
perform maintenance or repairs with unit running.
Always service and repair a cool unit. Disconnect the
spark plug wire to ensure that the unit cannot start.
FREQUENCY
MAINTENANCE REQUIRED
Fill fuel tank with fresh fuel
REFER TO
Page 9
Page 13
Before starting engine
Every 10 hours
Check oil
Clean and re-oil air filter
Page 14
First change at 10 hours
Every 25 hours thereafter
Every 25 hours
Change oil
Change oil
Clean spark arrestor
Page 13
Page 13
Page 17
Every 25 hours
Check spark plug condition and gap
Page 17
TINE REMOVAL AND REPLACEMENT
CHECKING THE OIL LEVEL
All 4 tines should be replaced at the same time because they will
wear evenly through normal use. Work on one side at a time.
CAUTION: To prevent extensive engine wear
and damage to the unit, always maintain the proper
oil level in the crankcase. Never operate the unit
with the oil level below the bottom of the dipstick.
WARNING: To prevent serious personal injury,
always wear heavy gloves when handling the
tines.
The importance of checking and maintaining the proper oil
level in the crankcase cannot be overemphasized. Check oil
before each use:
1.
Put the On/Off Stop Control in the STOP (O) position
and disconnect the spark plug wire.
NOTE: It may be necessary to lay the cultivator back in a
horizontal position on a flat level surface with the
upper handle touching the ground.
1.
2.
Stop the engine and allow oil to drain into the crankcase.
Place the unit on a flat, level surface to get a proper oil
level reading (Fig. 9).
2.
Remove the click pin from each end of the tine shaft. Slide
the tines off of the shaft (Fig. 14).
3.
Keep dirt, grass clippings and other debris out of the
engine. Clean the area around the oil fill plug/dipstick
before removing it.
4.
5.
Remove the oil fill plug/dipstick and wipe off oil. Reinsert it
all the way back in.
Remove the oil fill plug/dipstick and check the oil level. Oil
should be up to the top of the dipstick (Fig. 15).
“A” Tine
Oil Fill Plug/Dipstick
O-Ring
Full
“B” Tine
Click Pin
Hubs
Add 1.4-1.5 Oz.
(41-44 ml)
Fig. 14
3.
4.
Clean and oil the shaft.
Slide on the new tines with the hubs facing out. The four
tines are marked with the letters “A” or “B.”
Top of Dipstick
Fig. 15
5.
6.
Place one “A” tine and one “B” tine onto the shaft.
Secure the new tines to the shaft with click pins. It may be
necessary to wash the dirt off the tines and shaft for ease
of removal.
6.
If the level is low, add a small amount of oil to the oil fill hole
and recheck (Fig. 16). Repeat this procedure until the oil level
reaches the top of the dipstick.
NOTE: Do not overfill the unit.
10
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals |
|---|---|
| Tags | MTD TB144, Troy-Bilt TB144 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Product Type | Walk Behind Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)