MTD White Outdoor SB1350W Snow Blower Owners Manual

SECTION 9:  MAINTENANCE
WARNING: Disconnect the spark plug
wire   and  ground   against   the  engine
before    performing     any    repairs    or
maintenance.
BELT REMOVAL AND REPLACEMENT
WARNING: Remove   the   spark   plug
wire  from  the  spark  plug  and  ground.
Drain  gasoline  from   the  fuel  tank,   or
place a piece of plastic film underneath
the  gas  cap  to  prevent  gasoline  from
leaking.
AUGERS
The augers are secured to the spiral shaft with two
shear bolts and hex lock nuts. See Figure 16. If you
hit a foreign object or ice jam, the snow thrower is
designed so that the shear bolts will shear.
If  the  augers  will  not  turn,  check  to  see  if  the  hex
bolts  have  sheared.  Two  replacement  shear  bolts
and hex lock nuts have been provided with the snow
thrower. When replacing bolts, spray an oil lubricant
into shaft before inserting new bolts.
Auger Belt
To remove and replace either the auger belt or the
drive belt, proceed with the following instructions:
1.   Disconnect chute directional control assembly at
the discharge  chute  by removing  the cotter  pin
and flat washer.
2.
Remove the plastic belt cover on the front of the
engine  by  removing  three  self-tapping  screws
and flat washers. See Figure 17.
Auger Shear Bolts
Belt
Cover
Self-Tapping
Screw
Flat Washer
Auger Shaft
Shave Plate
Hex Lock Nuts
Figure 16  
SHAVE PLATE AND SKID SHOES
The shave plate and skid shoes on the bottom of the
snow  thrower  are  subject  to  wear.  They  should  be
checked periodically and replaced when necessary.
Figure 17  
3.
Remove the large shoulder bolt and washer on
the  left  hand  side  of  the  engine  pulley  with  an
adjustable wrench. Refer to Figure 18.
NOTE: All   models  are  equipped   with  reversible
skid shoes.
NOTE: Reference to right hand or left hand side of
To  remove  skid  shoes,  remove  the  carriage  bolts,
Belleville washers and hex nuts which attach them to
the snow thrower. Reassemble new skid shoes with
the  carriage  bolts,  Belleville  washers  (cupped  side
goes against skid shoes) and hex nuts.
machine are observed from the operating position.
4.
Remove  the  cotter   pin  and  washer  from   the
ferrule in order to disconnect the auger idler rod
from  the  brake  bracket  assembly  as  shown  in
Figure 19.
To  remove  shave  plate, remove  the carriage  bolts,
Belleville washers and hex nuts which attach it to the
snow   thrower   housing.  Reassemble   new   shave
plate, making sure heads of the carriage bolts are to
the inside of the housing. Tighten securely.
5.
6.
Slip the auger control belt (the front belt) off the
engine pulley. Refer to Figure 19.
Pull  the  brake   bracket  assembly  towards  the
cable  guide  roller  and  unhook  the  auger  cable
Z fitting.
7.
Remove the top screws and lock washers which
attach the auger housing assembly to the frame
assembly. A 9/16”   wrench is required. Refer to
Figure 20.
11
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals, White Outdoor Snow Blower Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 24 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website