ENGLISH
5.
(Figure 18) Loosen the belt guide (9). Pull
the belt guide (9) away from the auger
drive pulley (10).
12.Adjust the belt guide (9). See “How To Ad-
just The Belt Guide” in the Maintenance sec-
tion.
3. (Figure 22) Move the friction wheel (4) to
the correct position.against the snap ring
(1).
6.
7.
Pull the idler pulley (3) away from the auger
drive belt (4).
13.(Figure 20) Install the bottom panel (2).
14.Tighten the bolts (3) on each side of the bot-
tom panel (2).
15.(Figure 17) Install the belt cover (1). Tighten
screw (2).
4. (Figure 8) Turn the adaptor (10) until the
ball joint (6) is aligned with the mounting
hole in the shifter rod (7). When aligned,
attach the ball joint (6) to the shifter rod (7).
5. (Figure 20) Install the bottom panel (2).
6. Tighten the bolts (3) on each side of the bot-
tom panel (2).
Remove the old auger drive belt (4) from
the auger drive pulley (10) and from the en-
gine pulley (11). Replace the auger drive
belt (4) with an original factory replacement
belt available from an authorized service
center.
16.
Check the adjustment of the cables. See
“How To Check And Adjust The Cables” in
the Maintenance section.
8.
Install the new auger drive belt (4) onto the
auger drive pulley (10) and onto pulley
17.
Connect the spark plug wire.
How To Replace The Friction Wheel
If the friction wheel is worn or damaged, the
snow thrower will not move forward. The friction
wheel must be replaced as follows.
(11).
How To Adjust The Belt Guide
1.
2. (Figure 17) Remove screw (2). Remove the
belt cover (1).
3. (Figure 2) Engage the auger drive lever (5).
4. (Figure 21) Measure the distance between
the belt guide (2) and auger drive belt (3).
The correct distance (4) is 1/8 inch (3.175
mm).
9.
Adjust the auger drive belt (4). See “How To
Adjust The Auger Drive Belt” in the Mainte-
nance section.
Adjust the belt guide (9). See “How To Ad-
just The Belt Guide” in the Maintenance sec-
tion.
(Figure 17) Install the belt cover (1). Tighten
screw (2).
Check the adjustment of the cables. See
“How To Check And Adjust The Cables” in
the Maintenance section.
Disconnect spark plug wire.
WARNING: Do not lubricate the
disc drive plate or the friction
wheel.
10.
1. (Figure 2) Remove the gas from the gas
tank. Stand the snow thrower up on the front
end of the auger housing (4).
11.
12.
WARNING: Drain the gasoline out-
doors, away from fire or flame.
5.
If an adjustment is necessary, loosen the
mounting bolt for the belt guide (2). Move
the belt guide (2) to the correct position
2. Disconnect the spark plug wire.
13.
14.
(Figure 20) Install the bottom panel (2).
Tighten the bolts (3) on each side of the bot-
tom panel (2).
(4). Tighten the mounting bolt for the belt
3.
(Figure 26) Loosen the bolts (3) on each
side of the bottom panel (2).
guide (2).
(Figure 17) Install the belt cover (1). Tighten
screw (2).
6.
7.
4.
5.
Remove the bottom panel (2).
15.
Connect the spark plug wire.
(Figure 27) Use a 3/16” allen wrench and
remove the fasteners that secure the right
axle clamp (30) to the axle (34).
Connect the spark plug wire.
How To Remove the Traction Drive Belt
6.
7.
Remove the right wheel (35), axle (34), axle
clamp (30), and washer (31).
(Figure 28) Use a 3/16” allen wrench and
remove the fasteners that secure the left
axle clamp (30) to the axle (11).
How To Adjust Or Replace The Friction
Wheel
If the snow thrower will not move forward, check
the traction drive belt for wear or damage. If the
traction drive belt is worn or damaged, replace
the belt as follows.
How To Check The Friction Wheel
1.
2.
Disconnect the spark plug wire.
8.
Remove the left wheel (10), axle (11), axle
clamp (30), and washer (31).
If the snow thrower will not move forward, check
the traction drive belt, the traction drive cable or
the friction wheel. If the friction wheel is worn or
damaged, it must be replaced. See “How To
Replace the Friction Wheel” in this section. If the
friction wheel is not worn or damaged, check as
follows.
Remove the auger drive belt. See “How To
Remove The Auger Drive Belt” in the Mainte-
nance section.
(Figure 18) Remove the e-ring (17) from
one end of the swing plate axle rod (18).
Remove the swing plate axle rod (18) to
allow the the swing plate to pivot forward.
9. (Figure 29) Remove the fasterners that se-
cure the axle suport (32). Remove the axle
suport (32), bushing (33), and drive
sprocket (12).
10.(Figure 30) Remove the four bolts (16) that
hold the bearings (7) on each side of the
hex shaft (8).
3.
1.
(Figure 2) Remove the gas from the gas
tank. Stand the snow thrower up on the front
end of the auger housing (4).
4.
5.
Remove the traction drive spring (16).
Remove the old traction drive belt (13) from
the traction drive pulley (14) and from the
engine pulley (15). Replace the traction
drive belt (13) with an original factory re-
placement belt available from an authorized
service center.
Install the new traction drive belt (13) onto
the traction drive pulley (14) and onto en-
gine pulley (15).
11. (Figure 31) Remove the hex shaft (8) and
bearings (7).
NOTE: Take special note of the position of
the washers (13) .
(Figure 23) Remove the three fasteners (4)
that hold the friction wheel (5) to the hub
(6).
WARNING: Drain the gasoline out-
doors, away from fire or flame.
12.
2.
3.
Disconnect the spark plug wire.
(Figure 20) Loosen the bolts (3) on each
side of the bottom panel (2).
6.
7.
13.(Figure 23) Remove the friction wheel (5)
from the hub (6). Slip the friction wheel (5)
off the hex shaft (8).
14.Assemble the new friction wheel (5) onto
hub (6) with the fasteners removed earlier.
15.(Figure 31) Install the hex shaft (8) and
bearings (7) with the four bolts removed ear-
lier.
4.
5.
Remove the bottom panel (2).
(Figure 2) Position the shift speed lever (6)
Make sure the traction drive idler pulley
in the lowest forward speed.
(12)
is properly aligned with the traction
6.
(Figure 22) Note the position of the friction
wheel (4). The correct distance “A” from the
right side of the friction wheel (4) to the out-
side of the motorbox is as follows:
drive belt (13).
Attach the traction drive spring (16).
Install the swing plate axle rod (18) and se-
cure with the e-ring (17) removed earlier.
(Figure 30) The bottom of the swing plate
8.
9.
Tire Size
Distance “A”
10.
Make sure the washers (17) are properly
installed in the original position. Also,
make sure the two washers (13) are prop-
erly aligned with the actuator arms (14).
12
16
and 13 inch
inch
4-1/8” (10.5 cm.)
4-5/16” (10.95 cm.)
(20)
must be positioned between the align-
ment tabs (19). Make sure the swing plate
is properly secured.
If the friction wheel (4) is not in the correct
position, adjust as follows.
(20)
NOTE: If the drive will not engage after
the traction drive belt has been replaced,
then check to make sure that the swing
plate is positioned between the alignment
tabs (19).
16.Make sure the hex shaft (8) turns freely.
17.To install the remaining parts, reverse the
above steps.
18.Check the adjustment of the friction wheel.
See “How To Adjust The Friction Wheel” in
this section.
How To Adjust The Friction Wheel
1. (Figure 2) Position the shift speed lever (6)
in the lowest forward speed.
2. (Figure 8) Loosen hex jam nut (9) on speed
select rod (2). Remove ball joint (6) from
11.
(Figure 18) Install and adjust the auger
drive belt (4). See “How To Remove The
Auger Drive Belt” in the Maintenance section.
19.Make sure the friction wheel and the disc
drive plate are free from grease or oil.
shifter rod (7).
F-031088L
18
| Categories | Murray Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Murray 627804X5A |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Murray 627804X5A Snow Blower Owners Manual 5.0 out of 5.0 based on 1 product reviews. This snow blower takes a lickin and keepsn tickin! It's easy to start and easy to operate. After the plows come through the snow blower cuts through the compacte3d snow like butter.