Simplicity 5 55 7 55 1691411 1691413 1691414 Snow Blower Owners Manual

Regular    Maintenance
NORMAL  CARE
Every  25
Care
See   Paae
H   o  u   r   s
.
Check   auger   gear   case   lubrication.*
Page
I
.
Lubricate
snowthrower.
I
Check   tire   pressure.
I
Paae
9
I
l
I
1
.
Change    engine   oil.**+
Clean   or  replace   spark   plug.+
Check   discharge    control.
I
.
I
I     *     I
Page
14
The   transmission  and   auger  gear   case   have  been   factory   lubricated  for   life.   If  lubricant   should   leak
out,   have  transmission   or  auger   gear   case  inspected   by   your  dealer.
**Change
original   oil  after   two   hours   of  operation.
See   your   engine  Owner’s   Manual.
OFF-SEASON  STORAGE
6. Check  the  operation of  the controls.  If  necessary,
lubricate  the snowthrower  to improve  operation  of the
spout  control.
Before you  store your  snowthrower  for the  off-season,
read the  Maintenance  and Storage  instructions  in the
Safety  Rules section  and take  the following  precautions:
7.
Store  snowthrower  in the  wheels down,  operating
If stored  in any other  position,  oil from
NOTE:  Gasoline, if  permitted  to stand  unused for  extend-
ed periods  (30  days or  more), may  develop gummy
deposits  which can  adversely  affect  the engine  carbure-
tor and  cause engine  malfunction.  To  avoid this  condi-
tion, add  a gasoline  stabilizer to  the fuel tank  or drain all
fuel from  the system  before placing  unit in  storage.
crankcase  could enter  cylinder head,  causing  a ser-
vice problem.  Store  in a protected  area and  cover for
additional
protection.
CHECK  AUGER  GEAR  CASE
LUBRICATION
1.
Prepare  your snowthrower   engine for  storage  accord-
ing to the  instructions  found in the  engine Owner’s
Manual.
1.
2.
Place the  snowthrower  on a  level surface.
Remove  the pipe  plug (A,  figure 6).  The lubricant
should be  level with  the hole.  If not,  add Simplicity
Winter  Weight Worm  Gear Oil  (available from  your
dealer).
2.
Lubricate  the snowthrower  as  described  in the
LUBRICATION   section.
3..
Clean  the snowthrower  thoroughly.  Coat  all exposed
bare metal  parts with  a good quality  paint (available
from you  dealer) or a  light film of grease,  oil or  auto-
motive  wax.
3.
Re-install  pipe  plug.
STARTING AFTER STORAGE
1.
Remove  the spark  plug and  wipe  dry. Crank  engine  a
few times  to blow  excess oil  out of  plug hole. Then
reinstall plug.
2.
3.
Fill fuel  tank  with fresh  gasoline  (unless a
er was used).
stabiliz-
Check to  be sure engine  fins are  clean and  air flow is
unobstructed.
4.
5.
Check  engine oil  and  lubricate  snowthrower.
Start the  engine outdoors.  Do  not run engine  at high
speeds  immediately  after  starting.
Figure  6.   Checking  Auger   Gear  Case   Lubrication
8
Product Specification
CategoriesSimplicity Snow Blower Manuals, Snow Blower Manuals
Tags, , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 20 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandSimplicity, Snow Blower
Document File TypePDF
Publishersimplicitymfg.com
Wikipedia's PageSimplicity Outdoor
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website