Toro Greensmaster Flex 8 Specifications Specs

Greensmaster   ® 300  & 300  Specifications*   (continued)
8-BLADE DPA CUTTING UNITS, 04610
11-BLADE DPA CUTTING UNITS, 04611
TRACTOR
These cutting units will mount on any Toro riding Greensmaster
Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws  Bench HOC range is  
062"- 297" (1 6-7 5 mm)  With high HOC kit, range is  285-1" (7 3-25 4 mm)  Effective HOC may vary depending on turf conditions
and bedknife installed
HEIGHT OF CUT
(HOC) RANGE
Reels are 5" (13 cm) in diameter, 21" (53 3 cm) in length  High carbon steel blades are welded to 5 stamped steel spiders, and heat
treated to RC 48-54 hardness  The reel is ground for diameter and concentricity, and backgrind
REEL WELDMENT
Two double row, self-aligning ball bearings, 30 +/- 1 mm inside diameter slip fit onto reel shaft with lock nut  Multiple seal barriers
on both sides of bearing for added protection  Reel position maintained by a wave washer with no adjusting nut  
REEL BEARINGS
MAINTENANCE
No grease zerks, sealed bearing design eliminates daily maintenance
The reel weldment shaft is a 1 375" (35 mm) diameter tube with drive inserts permanently pressed in both ends  A replaceable
floating coupler with an internal eight tooth spline is factory installed on the right end, and held in place by a snap ring  The floating
coupler may be moved to the other end when the cutting unit is used on the GR3250-D front right position
REEL DRIVE
FRAME
Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates
Aggresiveness stays constant throughout the life of the reel  Patented design
AGGRESSIVENESS
Replaceable single-edged, high carbon steel bedknife austempered to RC 48-55, fastened to a machined cast iron bedbar with  
13 screws  Tournament bedknife is standard  
BEDKNIFE
BEDKNIFE
ADjUSTMENT
Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to  0007" ( 018 mm)  bedknife movement for  
each position  
Front: Aluminum Wiehle , 2 5" (6 4 cm) diameter with sealed bearings and through-shaft  Option between full, narrow-spaced  
®
and wide-spaced roller   
Rear: Steel full, 2" (5 1 cm) diameter with sealed bearings and through-shaft
FRONT & REAR
ROLLERS
GRASS SHIELD
TOTAL WEIGHT
Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions
8-blade: 72 lbs  (32 7 kg) with aluminum Wiehle Roller   
11-blade: 75 lbs  (34 1 kg) with aluminum Wiehle Roller
DPA CUTTING UNIT OPTIONS
Part No.
Description
Height of Cut Range (REC)
Part No.
Description
Height of Cut Range (REC)
SERVICE
BEDKNIVES
93-4262
108-4303
94-4263
108-4302
Micro-Cut Bedknife
Extended Micro-Cut Bedknife
Tournament Bedknife
062- 188" (1 6-4 8 mm)
062- 188" (1 6-4 8 mm)
125- 375" (3 2-9 5 mm)
125- 375" (3 2-9 5 mm)
93-4264
94-6392
63-8600
Lo-Cut Bedknife (1/8)
Hi-Cut Bedknife
Fairway Bedknife
188-1 00" (4 8-25 4 mm)
312-1 00" (7 9-25 4 mm)
375-1 00" (9 5-25 4 mm)
Extended Tournament Bedknife
FULL ROLLER
NARROW-SPACED WIEHLE
WIDE-SPACED WIEHLE
SOLID STEEL ROLLERS
DAMPENING ROLLER KIT
Model 04625  Set of three (3) 2 5" +/- 03" (6 35 cm) diameter, with sealed bearings and through-shaft (steel tube)
Model 04626  Set of three (3) 2 5" +/- 03" (6 35 cm) diameter,  20" +/- 03" spacing with sealed bearings and through-shaft (aluminum)
Model 04627  Set of three (3) 2 5" +/- 03" (6 35 cm) diameter,  93" +/- 03" spacing with sealed bearings and through-shaft (aluminum)
Model 04628  Set of one (includes machined solid steel Front Narrow Wiehle Roller & solid steel Full Rear Roller)
Model 04629  Set of one (equips one DPA cutting unit)
Includes a set of three (3) grooming reels, 2 375" (6 03 cm) diameter,  028" ( 71 mm) thick heat treated spring steel, operating at
3,000 RPM  Powered by a six (6) rib Poly-V-Belt   
Model 04632  Kit contains three for GR3050/3100/3150  
GROOMER
Model 04633  Kit contains three for GR3250-D
POWERED REAR
ROLLER BRUSH
Model 04640  Includes three brush assemblies  Fits GR3050/3100/3150  
Model 04641  Includes three brush assemblies  Fits GR3250-D
P/N 108-6468  One front roller scraper (narrow-spaced Wiehle)  
P/N 110-3961  One front roller scraper (wide-spaced Wiehle)  
P/N 110-3962  One front roller scraper (full roller)  
P/N 110-3963  One front roller scraper w/brush (narrow-spaced Wiehle)  
P/N 110-3964  One front roller scraper w/brush (wide-spaced Wiehle)  
P/N 110-3965  One front roller scraper w/brush (full roller)  
P/N 110-3966  One front roller scraper w/poly comb (narrow-spaced Wiehle)  
P/N 110-3967  One front roller scraper w/poly comb (wide-spaced Wiehle)  
P/N 110-3968  One front roller scraper w/poly comb (full roller)  
P/N 112-9353  One rear roller scraper
ROLLER
SCRAPER KITS
HIGH HEIGHT OF CUT KIT
5 BLADE HEAVY DUTY REEL
8 BLADE HEAVY DUTY REEL
GROOMER BRUSH ASSY.
P/N 106-4699  For one cutting unit
P/N 106-2626  One reel weld assembly
P/N 107-9522  One reel weld assembly
P/N 112-9460  One brush
*Specifications and design subject to change without notice
The Greensmaster 3050 & 3100 are manufactured in
Tomah, WI  ISO 9002 Certified Plant

Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 10 pages
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website