Greensmaster 30 Specifications*
®
GREENSMASTER 3150, MODEL 04357
18 hp (13 4 kW) Briggs & Stratton® gasoline engine, governed to 2850 rpm high idle, 1650 rpm low idle Air cooled, 34 8 cu in (570 cc)
7 gallon (26 5 liter) capacity; unleaded gasoline
ENGINE
FUEL CAPACITY
TRACTION DRIVE
GROUND SPEED
TURF COMPACTION
IMPLEMENT DRIVE
STEERING
2 or 3WD w/ROPS, hydrostatic piston pump closed loop system Foot pedal forward and reverse; infinitely variable
Forward — 1st, mow: 3 8 mph (6 1 km/h); 2nd, transport: 8 1 mph (13 km/h) Reverse — 1 9 mph (3 km/h)
8-10 psi (dependent on tire pressure) with operator and cutting units down
Single gear pump, mono valve block, series reel drive to 3 reel motors
Power steering Adjustable steering wheel tilt and a 5-position steering arm tilt
12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F and 34 minutes reserve capacity at 85° F/25 amps
draw 16 amp alternator Ignition switch/key Seat switch Harness terminals and fuse slot available for optional lights installation
ELECTRICAL FEATURES
CONTROLS/GAUGES
Raise/lower-mow lever (joystick) Functional control lever (neutral, mow, transport) Foot operated traction drive and brakes Hour
meter Hand operated throttle and choke Mechanical engine speed control
TIRES/WHEELS/
PRESSURE
Three tires: 18 x 9 50-8, 2-ply pneumatic, tubeless, demountable and interchangeable with smooth tread
Tire pressure: 8-12 psi (55-83 kPa) Optional Traction Tire (2-ply): P/N 231-127
BRAKES
HYDRAULIC OIL
LEAK DETECTION
SOUND LEVEL
Two 6" (15 2 cm) drum type
7 5 gallon (28 4 liter) tank with internal baffle 1 0 gallon (3 8 liter) auxiliary tank
Equipped with Turf Guardian™ leak detection system
81 dB(A) at operator’s ear under normal conditions
Wheel Tread: 49 5" (149 9 cm), Wheel Base: 47" (119 cm), Length: 90" (229 cm), Width: 69 75" (177 cm) w/reels, Height: 48 5" (123
cm), Weight (no reels): 970 lbs (440 kg), Weight w/reels (no fuel, no operator): 1,256 lbs (570 kg)
OVERALL DIMENSIONS
WIDTH OF CUT
REEL SPEED
59" (150 cm)
Approximately 1975 RPM at 2850 engine RPM
Standard equipment
BACKLAPPING
Cutting units are completely free-floating, each attaching to the tractor by direct pull links and lifted by a centered lift arm Baskets
are supported by carrier frames that are ground following Cutting unit floatation is unaffected by basket content Grass baskets are
all interchangeable and accessible from the front of the machine
CUTTING UNIT
SUSPENSION
OPTIONAL ACCESSORIES
WARRANTY
3WD kit w/ROPS, traction tire, thatching reels, spiker, tri-roller
Two-year limited warranty Refer to the Operator’s Manual for further details Briggs & Stratton provides a two-year commercial
engine, and a lifetime Magnetron® ignition warranty
8 BLADE DPA CUTTING UNITS, 04610
11 BLADE DPA CUTTING UNITS, 04611
TRACTOR
These cutting units will mount on any Toro riding Greensmaster
Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws Bench HOC range is
062"- 297" (1 6-7 5 mm) With high HOC kit, range is 285-1" (7 3-25 4 mm) Effective HOC may vary depending on turf
conditions and bedknife installed
HEIGHT OF CUT
(HOC) RANGE
Reels are 5" (13 cm) in diameter, 21" (53 3 cm) in length High carbon steel blades are welded to 5 stamped steel spiders, and heat
treated to RC 48-54 hardness The reel is ground for diameter and concentricity, and backgrind
REEL WELDMENT
Two double row, self-aligning ball bearings, 30 +/- 1 mm inside diameter slip fit onto reel shaft with lock nut Multiple seal barriers
on both sides of bearing for added protection Reel position maintained by a wave washer with no adjusting nut
REEL BEARINGS
MAINTENANCE
No grease zerks, sealed bearing design eliminates daily maintenance
The reel weldment shaft is a 1 375" (35 mm) diameter tube with drive inserts permanently pressed in both ends A replaceable
floating coupler with an internal eight tooth spline is factory installed on the right end, and held in place by a snap ring The floating
coupler may be moved to the other end when the cutting unit is used on the GR3250-D front right position
REEL DRIVE
FRAME
Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates
Aggresiveness stays constant throughout the life of the reel Patented design
AGGRESSIVENESS
Replaceable single edged, high carbon steel bedknife austempered to RC 48-55, fastened to a machined cast iron bedbar with
13 screws Tournament bedknife is standard
BEDKNIFE
BEDKNIFE
ADjUSTMENT
Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to 0007" ( 018 mm) bedknife movement for
each position
Front: Aluminum Wiehle , 2 5" (6 4 cm) diameter with sealed bearings and through-shaft Option between full, narrow-spaced and
®
wide-spaced roller
Rear: Steel full, 2" (5 1 cm) diameter with sealed bearings and through-shaft
FRONT & REAR
ROLLERS
GRASS SHIELD
TOTAL WEIGHT
Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions
8-blade: 72 lbs (32 7 kg) with aluminum Wiehle Roller
11-blade: 75 lbs (34 1 kg) with aluminum Wiehle Roller
*Specifications and design subject to change without notice
3
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Greensmaster Flex 8 |
| Download File |
|
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)