Reelmaster
®
4000-D Specifications* (continued)
REELMASTER 5, 7 OR 11 BLADE CUTTING UNITS
Five 30" (76 cm) wide hydraulically driven cutting units. Heavy duty welded steel cutting unit frame with 8" (20.3 cm) diameter welded
steel reels in self aligning bearings. Reel adjusted to bedknife with precision screw adjustment on ends of reel.
TYPE OF CUTTER
CUTTING UNIT
CONSTRUCTION
Welded steel frame, welded reel with heavy duty, self aligning bearings. Precision machined cast iron bearing housings support reel.
Bedbar and rear roller are isolation-mounted in rubber bushings. Adjustable deflector shields standard.
REEL
CONFIGURATION
8" (20.3 cm) diameter reels. 5, 7 or 11 blade reels available.
Heavy duty, all welded construction with induction hardened alloy steel blades.
Patented cutting unit head using heavy duty U-joint provides precision mounting; choice of 1-axis or 2-axis cutting unit flotation. The
fixed head, 1-axis flotation is suitable where ground contours are minimal. High strength forged alloy steel pivot with sealed needle
bearings for all direction free flotation. Equal length lift arms act uniformly on all five cutting units. Counterbalance force is adjustable
to match the cutting unit options installed and local conditions. Plated lift arm pivot and cylinder pins.
CUTTING UNIT
SUSPENSION
Replaceable single edged high carbon alloy steel bedknife mounted to the bedbar with screws.
Precision machined bedknife and bedbar.
BEDKNIFE/BEDBAR
REEL TO BEDKNIFE
ADJUSTMENT
Reel is adjusted to bedknife with precision screw-type adjusters.
Stainless steel and sintered bronze components.
3.5" (9 cm) diameter, heavy duty rear roller with bearings and seals. Roller bearings are greased through protected fittings on shaft
ends. Steel roller has greaseable tapered roller bearings with double lip seal. Zinc plate shaft for long, trouble-free service in
corrosive/high moisture environments. Optional Wiehle or full front rollers for floating cutting units. Side Skid Kit available for fixed
position cutting units.
REAR ROLLER
HEIGHT OF CUT
ADJUSTMENT
Heavy duty casting supports on either end of roller are adjustable for different HOC ranges. Supports locked in place on stainless
steel shaft with two self centering steel nuts.
5 Blade Cutting Unit
1" - 4" (25 - 102 mm)
0.176" clip per mph
7 Blade Cutting Unit
1/2" - 2" (12.7 - 51 mm)
0.126" clip per mph
11 Blade Cutting Unit
3/8" - 1" (9.5 - 25 mm)
0.080" clip per mph
Recommended Height of Cut range:
Clip Frequency (adjustable):
HEIGHT OF CUT &
CLIP FREQUENCY
(4.47 mm per 1.609 km/h)
(3.2 mm per 1.609 km/h)
(2.03 mm per 1.609 km/h)
Multiply clip by operating speed. All @ 1200 rpm maximum reel speed.
No. of Cutting Units:
Width of Cut:
1
29.5" (75 cm)
3
83" (211 cm)
4
110" (279 cm)
5
137" (348 cm)
WIDTH OF CUT
Up to 10.5 acres (4.25 hectares) per hour maximum at 7.5 mph (12 km/h); assumes no overlap or reduction due to turns, stops,
or adverse conditions.
CUTTING CAPACITY
THATCHING REELS
Model 03730; left, 2 required per machine. Model 03732: right, 3 required per machine. Skids are included with each unit.
The fixed head mount kit is recommended to facilitate the mounting of thatching reels.
THATCHING UNITS
THATCHING WIDTH
PENETRATION DEPTH
REEL CONSTRUCTION
Effective width per unit 27" (68.5 cm); overall width of set of 5 units 134" (340 cm).
Infinitely variable through rear roller up to a maximum depth of 1.12" (28 mm).
Reel diameter: 9" (23 cm). Hardened steel blades are .105" (2.7 mm) thick. Spacing between blades 1.25" (31.8 mm).
REELMASTER 4000-D ACCESSORY MATRIX
5 Blade
7 Blade
11 Blade
Thatching
Reels
Model 03730/L
Model 03732/R
Cruise
Control Kit
Model 03770
4-Post
Service
Manual
94-817-SL
Cutting Units
Model 03752/L
Model 03753/R
Cutting Units
Model 03723/L
Model 03724/R
Cutting Units
Model 03725/L
Model 03726/R
Roll Over
Protective
Structure
2 Wheel Drive Traction Unit, Model 03706
4 Wheel Drive Traction Unit, Model 03707
Flotation Mounting Kit (5), Model 03760
Wiehle Front Roller Kit (5), Model 03740
Rear Roller Scraper Kit (1), P/N 59-6090
Front Roller Scraper Kit (1), P/N 62-6220
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Std.
Opt.
Opt.
Opt.
Opt.
Opt.
Std.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Opt.
Std.
-
-
-
-
-
Opt.
-
-
-
-
-
-
-
-
-
-
-
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in design, required attachments and safety features. Consult your local Toro Distributor.
The Reelmaster 4000-D is manufactured
in Tomah, WI ISO 9002 Certified Plant.
- 2 of 2
- « Previous
- 1
- 2
| Categories | Lawn Mower Manual, Toro Lawn Mower Manual |
|---|---|
| Tags | Toro Reelmaster 4000-D |
| Download File |
|
| Document Type | Specifications |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)