Toro Reelmaster 4000 D Specifications 4000 D 2WD ENGINE RADIATOR OIL FUEL Specifications

Reelmaster   4000-D  Specifications*   (continued)
®
REELMASTER 5, 7 OR 11 BLADE CUTTING UNITS
Five 30" (76 cm) wide hydraulically driven cutting units  Heavy duty welded steel cutting unit frame with 8" (20 3 cm) diameter
welded steel reels in self aligning bearings  Reel adjusted to bedknife with precision screw adjustment on ends of reel
TYPE OF CUTTER
CUTTING UNIT
CONSTRUCTION
Welded steel frame, welded reel with heavy duty, self aligning bearings  Precision machined cast iron bearing housings support
reel  Bedbar and rear roller are isolation-mounted in rubber bushings  Adjustable deflector shields standard
REEL
CONFIGURATION
8" (20 3 cm) diameter reels  5, 7 or 11 blade reels available   
Heavy duty, all welded construction with induction hardened alloy steel blades
Patented cutting unit head using heavy duty U-joint provides precision mounting; choice of 1-axis or 2-axis cutting unit flotation  
The fixed head, 1-axis flotation is suitable where ground contours are minimal  High strength forged alloy steel pivot with sealed
needle bearings for all direction free flotation  Equal length lift arms act uniformly on all five cutting units  Counterbalance force is
adjustable to match the cutting unit options installed and local conditions  Plated lift arm pivot and cylinder pins
CUTTING UNIT
SUSPENSION
Replaceable single edged high carbon alloy steel bedknife mounted to the bedbar with screws   
Precision machined bedknife and bedbar
BEDKNIFE/BEDBAR
REEL TO BEDKNIFE
ADjUSTMENT
Reel is adjusted to bedknife with precision screw-type adjusters   
Stainless steel and sintered bronze components
3 5" (9 cm) diameter, heavy duty rear roller with bearings and seals  Roller bearings are greased through protected fittings on
shaft ends  Steel roller has greaseable tapered roller bearings with double lip seal  Zinc plate shaft for long, trouble-free service in
corrosive/high moisture environments  Optional Wiehle or full front rollers for floating cutting units  Side Skid Kit available for fixed
position cutting units
REAR ROLLER
HEIGHT OF CUT
ADjUSTMENT
Heavy duty casting supports on either end of roller are adjustable for different HOC ranges  Supports locked in place on stainless
steel shaft with two self centering steel nuts
5 Blade Cutting Unit
1" - 4" (25 - 102 mm)
0 176" clip per mph
7 Blade Cutting Unit
5" - 2" (12 7 - 51 mm)
0 126" clip per mph
11 Blade Cutting Unit
375" - 1" (9 5 - 25 mm)
0 080" clip per mph
Recommended Height of Cut range:
Clip Frequency (adjustable):
HEIGHT OF CUT &
CLIP FREqUENCY
(4 47 mm per 1 609 km/h)
(3 2 mm per 1 609 km/h)
(2 03 mm per 1 609 km/h)
Multiply clip by operating speed  All @ 1200 rpm maximum reel speed
No. of Cutting Units:
Width of Cut:
1
29 5" (75 cm)
3
83" (211 cm)
4
110" (279 cm)
5
137" (348 cm)
WIDTH OF CUT
Up to 10 5 acres (4 25 hectares) per hour maximum at 7 5 mph (12 km/h); assumes no overlap or reduction due to turns, stops,  
or adverse conditions
CUTTING CAPACITY
THATCHING REELS
Model 03730; left, 2 required per machine  Model 03732: right, 3 required per machine  Skids are included with each unit   
The fixed head mount kit is recommended to facilitate the mounting of thatching reels
THATCHING UNITS
THATCHING WIDTH
PENETRATION DEPTH
REEL CONSTRUCTION
Effective width per unit 27" (68 5 cm); overall width of set of 5 units 134" (340 cm)
Infinitely variable through rear roller up to a maximum depth of 1 12" (28 mm)
Reel diameter: 9" (23 cm)  Hardened steel blades are  105" (2 7 mm) thick  Spacing between blades 1 25" (31 8 mm)
REELMASTER 4000-D ACCESSORY MATRIX
5 Blade  
7 Blade
11 Blade
Thatching
Reels
Model 03730/L
Model 03732/R
4-Post
Cutting Units
Model 03752/L
Model 03753/R
Cutting Units
Model 03723/L
Model 03724/R
Cutting Units
Model 03725/L
Model 03726/R
Roll Over
Protective  
Structure
Service
Manual
94-817-SL
2 Wheel Drive Traction Unit, Model 03706
4 Wheel Drive Traction Unit, Model 03707
Flotation Mounting Kit (5), Model 03760
Wiehle Front Roller Kit (5), Model 03740
Rear Roller Scraper Kit (1), P/N 59-6090
Front Roller Scraper Kit (1), P/N 62-6220
Opt
Opt
Opt
Opt
Opt
Opt
Opt
Opt
Opt
Std
Opt
Opt
Opt
Opt
Opt
Std
Opt
Opt
Opt
Opt
Opt
Opt
Std
-
-
-
-
-
Opt
-
-
-
-
-
-
-
*Specifications and design subject to change without notice  Products depicted in this literature are for demonstration purposes only
Actual products offered for sale may vary in design, required attachments and safety features  Consult your local Toro Distributor
The Reelmaster 4000-D is manufactured
in Tomah, WI  ISO 9002 Certified Plant
54
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 2 pages
Document TypeSpecifications
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website