Toro TS90T Installation Instructions 090320 Catalog

Sprinkler Installation
Figure 2
1.
2.
3.
Construct or install manufactured triple swing  joints for each sprinkler. See Figure 2.
Flush lines thoroughly prior to installing  sprinkler.
Apply PTFE pipe thread tape to  the sprinkler nipple threads. Install the sprinkler to the
nipple, tightening by hand to a  snug fit.
CAUTION: Use only PTFE tape on plastic thread  connections. Applying pipe dope
or other thread-sealing compounds can cause  deterioration of plastic threads.
Arc Adjustment
The TS90 series sprinkler features both an  adjustable arc from 40° to 330°, in 5° increments,
and full-circle 360° operation. All TS90 series sprinklers are  preset to half-circle (180°) arc
when shipped from the factory.
Figure 3
The left side of the adjustable  arc is fixed, and is aligned to the left watering  border by
turning the ratcheting riser assembly in  the sprinkler body. The right side of the arc is aligned
to the right watering border by  turning the nozzle turret while compressing and holding the
adjustment band in a stationary position.
+
1.
Arc adjustment can be made wet  or dry. For dry adjustment, insert the blade of the
sprinkler tool (included in carton) through  the slitted opening in the top of the nozzle turret.
Twist the tool 1/2 turn to  catch the inside of the nozzle turret, then pull the  riser assembly
out of the body until fully  extended. Grasp the riser below the gray adjustment band and
hold firmly to prevent retraction. See  Figure 3.
Figure 4
Note: Specific arc settings of 90°,  180°, 270° and 360° are provided on the adjustment
band to preset the sprinkler arc  if desired. To use this adjustment option, simply compress
the serrated portion of the adjustment  band and turn it to align the preferred arc indicator
with the nozzle turret arrow indicator.  See Figure 4.
90°
180°
2.
3.
Find the sprinkler left and right  arc limits by rotating the nozzle turret back and forth  (in the
direction of free travel only). The left  stop indicates the fixed (non-adjustable) side of the
arc. See Figure 5.
270°
360°
CAUTION: Do not force the nozzle turret past  the arc travel limits. Permanent
damage to the drive assembly can  result.
With the nozzle turret rotated to  the left stop, align the nozzles to the left watering  border
by ratcheting the riser assembly in  either direction. See Figure 6.
Figure 5
+
4.
5.
Find the sprinkler right stop by  rotating the turret clockwise until it stops.
To adjust the arc, compress the  ribbed area of the adjustment band, then rotate the nozzle
turret to align the nozzles with  the right watering border. For full-circle operation, rotate the
nozzle turret to the right until  it stops. See Figure 7.
6.
With the sprinkler on, check arc  setting again and fine tune arc setting as needed.
Main Nozzle Trajectory Adjustment
Figure 6
The main nozzle trajectory angle is  factory-set at 25°, and is adjusted between 7°—30°
by turning the trajectory adjustment nut,  accessible through the top of the nozzle turret.
Typical uses of this feature are  to increase trajectory to compensate for high-mounded turf,
or to decrease trajectory to clear  low-hanging tree branches.
Note: Prior to changing the nozzle  trajectory, it is important to consider that increasing the
trajectory increases the spray radius, and  decreasing trajectory decreases the spray radius.
1.
Using Toro service tool 995-105 or a
5/16″ nut driver, turn the adjustment
Figure 8
Figure 7
+
nut clockwise to decrease trajectory or
counterclockwise to increase trajectory,
as indicated by the bidirectional arrow.
See Figure 8.
30°
30°
©
2009 The Toro Company, Irrigation Division • www.toro.com  • 1-877-345-8676
Form Number 373-0536 Rev. A
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 2 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website