Yard Machines E740 E760 Snow Blower Owners Manual by MTD

SECTION 5:  ASSEMBLY INSTRUCTIONS
NOTE: Reference to  right or left  side of the  snow
thrower can  be  determined from  behind the  unit
in the operating position.
UNPACKING
1.
Remove staples or  break glue on the top  flaps of
the  carton.   Remove  any  loose   parts  included
with unit (i.e., operator’s manual, etc.).
Cut  along  dotted   lines  and  lay  end   of  carton
down flat. Remove packing material.
Roll  unit out  of carton.  Check  carton thoroughly
for loose parts.
Lay out the  hardware according to the  illustration
on page 5 for identification purposes.
2.
3.
4.
Left
Handle
Right
Handle
Tools Required for Assembly:
(1)
(2)
(1)
(1)
(1)
3/8" Wrench or Adjustable
7/16" Wrenches or Adjustable
1/2" Wrench or Adjustable
Pair of Pliers
Flat
Phillips Screwdriver
Loose Parts in Carton:
(1)
(1)
(1) Right Handle
(1) Left Handle
Handle Panel        (1) Chute Crank Assembly
Chute Assembly    (1) Shift Rod
(1) Hardware Pack
Figure 2
ATTACHING THE HANDLE ASSEMBLY
(Hardware A)
1.
Stretch out  control cables and  place on  the floor
behind unit.
2.
Identify left  and right  handles as shown  in figure
2.
The flats  on the  lower part  of  handles will  be
placed against the snow thrower housing.
Place   right  handle   in   position   with   flat  side
against the  snow thrower. Secure  bottom hole in
handle   to snow thrower using  hex bolt 3/4"  long
and lock  washer. See figure  3. Do  not tighten at
this time.
Place handle  tab over  the upper  hole in  handle,
so the curve in  the handle tab matches the  curve
in the  handle. Secure  to the snow  thrower using
3.
4.
Lock
Washers
Hex Bolt
Long
Handle
Tab
3/4"
Hex
Bolt 1-3/4"
Long
1-3/4"
at this time.
hex  bolt and  lock washer.  Do  not tighten
Figure 3
5.
6.
Attach  the left  handle  in  the  same manner.  Do
not tighten at this time.
Handle Panel
Place  the handle  panel  in position  between  the
handles.  To   hold   the  handle   panel  in   place,
engage both  clutch grips  (hold them  against the
handles).   Now release  the left  hand grip, and  it
will remain  against the  handle. Keep holding  the
right hand clutch grip. See figure 4.
Cupped  Hex
Washer
Nut
7.
Secure  the  right   side  of  the  handle   panel  by
inserting carriage bolt through  handle and handle
panel  (must   go  through   both  the   plastic  and
metal  parts  of  the  handle   panel).  Secure  with
cupped washer  (cupped side  against the  handle
panel)   and   hex   nut.    Repeat   using   another
carriage bolt, cupped washer and hex nut.
Secure  the left  side  of  the  handle panel  in  the
same manner.
NOTE:
Place the cupped
side against the
handle panel.
Carriage
Bolt
8.
9.
Figure 4
Tighten   the  four   hex   bolts  which   attach   the
bottom of the handles to the snow thrower frame.
6
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals, Yard Machines Snow Blower Manuals
Tags, , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandYard Machines, E740, E760, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website