Drift Cutters
Drift cutters should be used when operating the snow
thrower in heavy drift conditions.
(If Equipped)
WARNING: The temperature of the muffler
and the surrounding areas may exceed
150°
F. Avoid these areas.
If your unit is not equipped with drift cutters, contact
Customer Support as instructed on page 2 for
information regarding price and availability.
•
For the most efficient snow removal, remove snow
immediately after it falls.
Discharge the snow downwind whenever possible.
Slightly overlap each previous path.
Set the skid shoes 1/4" below the shave plate for
normal usage. The skid shoes may be adjusted
upward (to lower the shave plate) for hard-packed
snow. Adjust downward (to raise the shave plate)
when using on gravel or crushed rock.
Be certain to follow the precautions found in the To
Stop Engine section to prevent possible freeze-up.
Clean the snow thrower thoroughly after each use.
•
•
•
Snow Thrower Model
Drift Cutter Kit
All models
OEM-390-679
Operating Tips
NOTE: Allow the engine to warm up for a few minutes.
The engine will not develop full power until it reaches
operating temperature.
•
•
SECTION 5: ADJUSTING YOUR SNOW THROWER
WARNING: NEVER attempt to make any
adjustments while the engine is running,
except where specified in the operator’s
manual.
If you are uncertain that you have reached the correct
adjustment, proceed as follows:
WARNING: Drain the gasoline out of the
snow thrower’s tank, or place a piece of
plastic film under the gas cap to avoid
spillage BEFORE making the adjustment.
Auger Control
Refer to Auger Control Test in the Operating Section to
adjust the auger control.
•
Tip the snow thrower forward, allowing it to rest on
the auger housing. See Figure 8.
Drive Control and Shift Lever
Frame Cover
To check the adjustment of the drive control and shift
lever, proceed as follows:
•
To check the adjustment of the traction control
clutch and shift lever, proceed as follows:
With the engine off, move the shift lever all the way
forward to the highest speed. With the drive control
released, push the snow thrower forward. The unit
should roll forward. Then engage the drive control.
The wheels should stop turning.
•
•
•
Now release the drive control and push the unit
again.
Move the shift lever back to the fast reverse
position then all the way forward again. There
should be no resistance in the shift lever, and the
wheels should keep turning.
Auger
Housing
•
If you have resistance when moving the shift lever
or the wheels stop when they should not, loosen
the jam nut on the drive control cable and unthread
the cable one turn.
Figure 8
•
•
If the wheels do not stop when you engage the
drive control, loosen the jam nut on the drive control
cable and thread the cable in one turn.
Recheck the adjustment and repeat as necessary.
Tighten the jam nut to secure the cable when
correct adjustment is reached.
•
•
Remove the frame cover underneath the snow
thrower by removing the six self-tapping screws.
With the drive control released, there must be
clearance between the friction wheel and the drive
plate in all positions of the shift lever.
10
| Categories | MTD Snow Blower Manuals, Snow Blower Manuals, Yard Man Snow Blower Manuals |
|---|---|
| Tags | MTD 31AH7S3G701, MTD Snow Blower Manual |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Snow Blower, Yard-Man, 31AH7S3G701, Snow Blower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Yard-Man 31AH7S3G701 Snow Blower Owners Manual by MTD 4.0 out of 4.0 based on 1 product reviews. Helpful, informative