Yard-Man 31AH7S3G701 Snow Blower Owners Manual by MTD

SECTION 6:  MAINTAINING YOUR SNOW THROWER
WARNING:  Before  lubricating,  repairing,
or inspecting, disengage all controls and
stop  engine.  Wait  until  all  moving  parts
have come to a complete stop. Disconnect
spark plug wire and ground it against the
engine   to  prevent   unintended   starting.
Always    wear    safety     glasses    during
Auger Shaft
At least once a season, remove the shear pins on the
auger shaft. Spray lubricant inside the shaft and
lubricate the plastic auger bearings at least once a
season. See Figure 12.
Vent Plug
Shear Pin
operation
or    while     performing    any
adjustments or repairs.
Lubrication
Engine
Refer to the separate engine manual packed with your
unit for all engine lubrication instructions.
WARNING: If any adjustments need to be
made  to  the  engine  while  the  engine  is
running (e.g. carburetor), keep clear of all
moving parts. Be careful of muffler, engine
and other surrounding heated surfaces.
Plastic
Bearing
Bearings
Gear Shaft
Figure 12
Lubricate the gear shaft with 6-n-1 grease at least once
a season or after every 25 hours of operation (available
at automotive stores, or order part number 737-0170).
Refer to Figure 9.
Auger Bearings
Every season lubricate the auger bearings and the
bearings on the side of the frame with light oil. See
Figure 12.
IMPORTANT: Keep all grease and oil off of the rubber
friction wheel and aluminum drive plate.
Drive and Shifting Mechanism
Chute Directional Control
Lubricate at least once a season or after every 25 hours
of operation. Remove the rear cover, lubricate any
chains, sprockets, gears, bearings, shafts, and shifting
mechanism at least once a season. Use engine oil or a
spray lubricant. Avoid getting oil on the friction
wheel rubber and aluminum drive plate. Refer to
Figure 9.
The worm gear on the chute directional control
should be greased with multipurpose automotive
grease.
Gear Case
The gear case is lubricated with grease at the factory
and it does not require checking. If disassembled for
any reason, lubricate with 2 ounces of Shell Alvania
grease EPR00, part number 737-0168. Before
reassembling, remove old sealant and apply new
sealant. See Figure 12.
Drive / Auger Control Lock
The cams on the ends of the control rods which
interlock the drive and auger controls must be
lubricated at least once a season or every 25 hours of
operation. The cams can be accessed beneath the
handle panel. Use a multi-purpose automotive grease.
IMPORTANT: Do not overfill the gear case, since
damage to the seals could result. Be sure the vent plug
is free of grease in order to relieve pressure.   
12
Product Specification
CategoriesMTD Snow Blower Manuals, Snow Blower Manuals, Yard Man Snow Blower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower, Yard-Man, 31AH7S3G701, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Yard-Man 31AH7S3G701 Snow Blower Owners Manual by MTD 4.0 out of 4.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Yard-Man 31AH7S3G701 Snow Blower Owners Manual by MTD SKU UPC Model
Jon Steinmetz on Feb 17, 2014.

Helpful, informative


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website