Install Auger/Impeller Drive
Control Linkage
Install Chute Control Rod
1.
Assemble chute control bracket and rod to left
side of handle with capscrew and locknut. Leave
locknut loose until assembly is completely
mounted (Fig. 10).
1.
2.
3.
Loosen jam nut above clevis on upper control
rod (Fig. 8).
2.
Apply No. 2 general purpose grease to worm
gear. Next, mount worm gear and bracket to
mounting flange and secure with pyramidal
washer and locknut (Fig. 11).
Align holes in clevis and lower control rod and
insert clevis pin (Fig. 8).
Check the distance between the top of the
handgrip and the bottom of the auger/impeller
control lever (Fig. 6 & 9). Distance should be
approximately four inches. This is a
preliminary setting only.
3.
4.
5.
Slide worm gear into teeth of chute retaining
ring and tighten locknut (Fig. 11).
Tighten the locknut securing chute control
bracket against left handle (Fig. 10).
Check operation of chute control rod. Move
worm gear slightly outward if binding is evident.
4.
Compress auger/impeller control lever slowly
toward handgrip. The amount of force to
compress the lever will increase noticeably when
slack is removed from the drive belt
Secure Chute Deflector
(approximately one–half of lever movement).
Adjustment is correct when the force begins to
increase and the distance between the top of the
handgrip and the bottom of the auger/impeller
control lever is one to two inches.
1.
Pivot deflector upward and back until deflector
stop passes over lip on top of chute.
2.
Secure left side of deflector to discharge chute
using parts as illustrated in Figure 12. Make sure
rubber washer and friction plate are positioned
between chute and deflector and friction plate
tabs fit into holes in deflector. See Figure 12 for
proper installation sequence of parts.
Note:
If force does not noticeably increase,
remove the belt cover (refer to
Replacing Auger/ Impeller Drive Belt,
steps 1–2, page 15) and measure the
one to two inch dimension above the
handgrip at the point where the slack is
removed from the auger/impeller drive
belt.
Note:
Concave side of curved washer goes
against large flat washer.
3.
Tighten nuts on both sides of deflector. Do not
over–tighten nuts so that excessive force is
required to change deflector angle.
5.
6.
To adjust the distance, remove clevis pin, loosen
jam nut and thread clevis up or down to increase
or decrease distance between handgrip and
auger/impeller control lever (Fig. 8).
Check Tire Pressure
IMPORTANT: Check pressure of tires
because they are over–inflated at the factory
for shipping. Before the snowthrower is
operated, reduce pressure in both tires to
7–15 psi equally.
When adjustment is correct, install clevis pin
and secure it in place with the cotter pin. Tighten
jam nut to secure clevis (Fig. 8).
9
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38062, Toro 622, Toro 9900001 |
| Model Number | 38062 |
| Model Year | 1999 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 9900001 - 9999999 |
| Product Name | Toro 622 38062 Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Small Frame |
| Swath | 22 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 21 oz. (.62l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 7 oz. (198gm) Lubriplate MAG-1 |
| Engine Motor Model # | HSK60-76011C |
| Engine Motor Size | 6 hp |
| Engine Motor Type | 4 Cycle CARB1, EPA1 |
| Transmission Speed | 3 Forward/1 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(3 votes, average: 4.67 out of 5)
Lawn and Garden readers have rated Toro 622 38062 Snow Blower Operators Manual, 1999 4.7 out of 5.0 based on 3 product reviews. Fine snowblower, no complaints
Thank you very Much!!!!!!
5