Toro 824 1028 Power Shift 38542 and 38558 Snow Blower Operators Manual, 1999

4.
5.
Wait for all moving parts to stop before leaving
the operator’s position (behind the handles).
free wheels. By contrast, when both pins are installed
thru holes in wheel hub and inner hole of axle
(Fig. 21), snowthrower propels itself.
Store key in a memorable place.
Snowthrowing Tips
Power Shift Operation
1.
2.
3.
When snowthrower is not being used, close fuel
shut–off valve and remove key from the switch.
Wheels will shift forward (or rearward) with every
other movement of the shift control.
Remove snow as soon as possible after it falls.
This produces best snow removal results.
Move wheels to the rear Power Shift position in
heavy and/or drifted snow.
When in the rear Power Shift position, push
down on handles to increase traction if
necessary.
Leave wheels in the front position for light snow or
for transporting snowthrower.
1.
2.
Release traction drive lever.
4.
5.
Discharge snow downwind whenever possible,
and overlap each swath to ensure complete snow
removal. If wheels slip, shift into a lower gear to
reduce forward speed.
To move wheels to front or rear position, move
shift control fully forward to Power Shift
position and hold (Fig. 19).
In some snow and cold weather conditions, some
controls and moving parts may freeze. Therefore,
when any control becomes hard to operate, stop
the engine and wait for all moving parts to stop;
then check all parts for freeze up. DO NOT USE
EXCESSIVE FORCE AND TRY TO OPERATE
THE CONTROLS WHEN FROZEN. Free all
controls and moving parts before operating.
3.
Fully engage traction drive lever to move wheels
into alternate position (Figs. 19 & 20).
Note:
When power shifting it may be
necessary to slightly raise handle to
assist wheel movement.
Note:
To shift wheels manually if engine is
not running, follow steps 1 and 2 and
then lift up on handles to unlock
wheels.
6.
7.
Adjust skids to match the type of surface being
cleaned. Refer to Adjusting Skids, page 14.
Run snowthrower for a few minutes after
clearing snow so moving parts do not freeze.
Engage auger/impeller to clear any remaining
snow from inside housing.
Note:
If wheels do not move in desired
direction when power shifting, repeat
procedure.
8.
9.
Do not overload snowthrower by clearing snow
at too fast a rate. If engine slows down, shift to a
lower gear to reduce forward speed.
Free Wheeling Or
Self–propelled Drive
Move wheels to the rear Power Shift position
and shift to a lower gear in heavy and/or drifted
snow to prevent the auger/impeller housing from
riding up over the snow.
The snowthrower can be free wheeled or engaged for
self–propelled operation. There are two holes in each
end of the axle. When axle pins are thru outer axle
holes and not thru wheel hub (Fig. 21), snowthrower
13
Product Specification
CategoriesSnow Blower Manuals, Toro Snow Blower
Tags, , ,
Model Number38542 and 38558
Model Year1999
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 32 pages
Document TypeOperator's Manual
LanguageEnglish
Serial Number99000001 - 99999999
Product NameToro 824 1028 Power Shift Snowthrower
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower
Product TypeSnowthrower
Product SeriesSnowthrower, Two Stage Power Shift
Swath24 inch
DischargeTwo Stage
Engine ManufacturerTecumseh
Engine Oil Type26 oz. (.8l) 5w-30 or 10w / API SH or higher
Engine Motor Model #4.5 oz. (133ml) SAE 90 GL5 or higher
Engine Motor Size8 hp
Engine Motor Type4 Cycle CARB1, EPA1
Transmission Speed4 Forward/2 Reverse
Transmission TypeGear
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(2 votes, average: 4.5 out of 5)
Lawn and Garden readers have rated Toro 824 1028 Power Shift 38542 and 38558 Snow Blower Operators Manual, 1999 4.5 out of 5.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 824 1028 Power Shift 38542 and 38558 Snow Blower Operators Manual, 1999 SKU UPC Model
Sören Fritiofsson on Jan 10, 2016. soren f on jan 10 2016

I have some problem not to drive without choke its running with smaller capacity


Ola f on Jan 12, 2015.

Stable but dont throw the snow long enough


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website