Adjusting the Control Cable
Important
you disengage the control bar for the rotor blades to stop
properly.
The control cable must contain slack when
Check the control cable for proper adjustment initially,
after the first operating hour, and then annually thereafter.
Adjusting the Cable
Checking the Cable
For Models 38515 and 38516 only:
1.
2.
Stop the engine and wait for all moving parts to stop.
1.
2.
Unhook the spring end from the control bar (Fig. 16).
Move the control bar back toward the handle to remove
the slack in the cable as shown in Figure 16 (for models
Slide the spring cover off the spring and the cable
adjuster (Fig. 18).
38515
and 38516) or Figure 17 (for models 38517 and
38518).
4
1
2
Models 38515
and 38516
897
1
2
3
4
Figure 18
4
3
1.
2.
Cable
3.
4.
Cable adjuster
Spring
Z-fitting
1
3.
Unhook the Z-fitting from the cable adjuster (Fig. 18)
and position the Z-fitting in a higher or lower hole on
the adjuster to obtain a proper gap of 1/16 to 1/8 in. (2
to 3 mm) between the control bar and the handle
(Fig. 16).
5
6
m-5533/m-2708
2
Figure 16
Note: Moving the Z-fitting to a hole closer to the spring
decreases the gap between the control bar and the
handle; moving it to a hole farther from the spring
increases the gap.
1.
Top hole
4.
5.
6.
Control bar
2.
3.
Bottom hole
Spring cover
1/16 to 1/8 in. (2 to 3 mm)
gap
Control cable
4.
Slide the spring cover over the cable adjuster and the
spring.
Models 38517
and 38518
5. Hook the spring into the bottom hole of the control bar.
2
3
6.
Check the adjustment (refer to steps 2 and 3 of
Checking the Cable on page 16).
4
1
5
m-5519
Figure 17
1.
Cable
4.
5.
Bottom hole
2.
3.
Control bar
Top hole
1/16 to 1/8 in. (2 to 3 mm)
gap
3.
Ensure that a 1/16 to 1/8 in. (2 to 3 mm) gap exists
between the control bar and the handle. Refer to the
inset in Figure 5 (models 38515 and 38516) or the inset
in Figure 9 (models 38517 and 38518). To adjust the
cable, go to Adjusting the Cable on page 16.
16
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38516, Toro CCR 2450 |
| Model Number | 38516 |
| Model Year | 2002 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 220000001 - 220999999 |
| Product Name | Toro CCR 2450 GTS Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | CCR 1000/2400/2500, Single Stage, Snowthrower |
| Swath | 20 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Toro |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | R-tek |
| Engine Motor Size | 5 hp |
| Engine Motor Type | 2 Cycle EPA1 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)