Toro 38025 1800 Power Curve Snowblower Manual, 2003-2009

5.
6.
Lift up the  idler arm and slip the belt  under the idler
pulley (Fig. 20).
Note: The bolt must  ride on bearings in the small
pulley.
Rotate the rotor with  your left hand while sliding  the
belt onto the  large pulley with your right hand
(Fig. 21).
7.   Place the new belt on  the small pulley.
8.
9.
Slide the belt over  the motor shaft pulley (Fig.  22).
When tightening the  bolt, the bolt head and  the
washers must be flush  against the small pulley. Torque
the bolt to 25 to  30 in-lb (2.8 to 3.4 Nm). Do  not
overtighten the bolt.
10.
Slip the large belt  over the small pulley (Fig.  21).
Refer to step 4  through 8 of Replacing the Large  Belt
on page 10.
1529
Storage
Figure 21
1.
Run the snowthrower for  a few minutes to melt away
any snow on the snowthrower.
7.
8.
Assemble the idler spring  (Fig. 18), making sure the
idler pulley rides  on the belt.
2.
3.
Disconnect the extension  cord from the snowthrower.
Install the left side  cover and the skid with the
Examine the extension  cord thoroughly for signs of
wear or damage. Replace  it if it is worn  or damaged.
3
screws.
4.
Examine the snowthrower  thoroughly for worn, loose,
or damaged parts.  For repairing or replacing parts,
contact your local  Authorized Service Dealer for
assistance.
Replacing the Small Belt
1.
Remove the screws  that secure the left side plate  and
the skid to the  snowthrower frame (Fig. 15), and
remove the side  plate and the skid.
5.
6.
Store the extension cord  with the snowthrower.
2.
Remove the large  belt by slowly sliding it off  the small
pulley (Fig. 19). Refer  to steps 2 and 3 of  Replacing
the Large Belt  on page 10.
Store the snowthrower in  a clean, dry place. Cover  it
to provide  protection.
Toro Service
Support
3.
4.
Remove the small  pulley bolt (left hand thread)  by
turning the bolt  clockwise.
Remove the 2 washers  and the small pulley (Fig. 22).
If your snowthrower  requires service or maintenance, your
nearest Toro Master  Service Dealer is the best  dealer to
assist you. Refer to  the “Yellow Pages” of your local
telephone directory in  the section titled “Lawn  Mowers.”
Toro Master Service Dealers  are listed under the Toro
trademark. If you  need help locating a Toro  Master
Service Dealer near  you, call 1-800-421-9684 for
assistance.
5
4
3
2
1
1530
Figure 22
1.
2.
3.
Bolt (left hand thread)
Washers
Small pulley
4.
5.
Small belt
Motor shaft pulley
5.
6.
Remove and discard  the small belt (Fig. 22).
Slide 2 washers onto  the bolt and insert the bolt
through the small  pulley.
11
Product Specification
CategoriesSnow Blower Manuals, Toro Snow Blower
Tags,
Model Number38025
Model Year2003, 2004, 2005, 2006, 2007, 2008, 2009
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 12 pages
Document TypeOperator's Manual
LanguageEnglish, Français
Serial Number230000001 - 230999999, 240000001 - 240999999, 250000001 - 250999999, 260000001 - 260999999, 270000001 - 270999999, 280000001 - 280999999, 290000001 - 290999999
Product Name1800 Power Curve Snowthrower
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower
Product TypeSnowthrower
Product SeriesSnowthrower
Swath18 inch
DischargeSingle Stage
Engine Motor Size12 amp
Engine Motor Type120-VAC
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website