18
Checking the Auger
Gearbox Oil Level
1.
around the oil drain
cap (A).
Clean the area
A
Check the auger gearbox oil annually, and add oil if
necessary.
m-4036
2.
Slide an oil drain pan under the drain extension
and remove the oil drain cap.
1.
2.
Move the snowthrower to a level surface.
Clean the area around the pipe plug.
3.
Drain the oil.
Note: Dispose of the used oil properly at a local
recycling center.
4.
5.
Engine Crankcase with Oil on page 9.
Install the oil drain cap.
Fill the crankcase with oil. Refer to Filling the
652
Lubricating the Hex Shaft
Lightly lubricate the hex shaft (A) annually.
m-6937
A
3.
4.
Remove the pipe plug from the gearbox.
Check the level of oil in the gearbox. The oil
should be at the point of overflowing at the filler
opening.
B
5.
If the level of oil is low, add GL-5 or GL-6,
SAE 85–95 EP transmission oil to the gearbox until
the point of overflow.
Note: Do not use synthetic oil.
C
m-6967
6.
Install the pipe plug in the gearbox.
Important: Do not get oil on the rubber wheel (B) or
the aluminum friction drive plate (C) because the
traction drive will slip.
Changing the Engine Oil
1.
2.
Drain the gasoline from the fuel tank.
Change the engine oil after the first 2 operating hours,
then annually thereafter. If possible, run the engine
just before changing the oil because warm oil flows
better and carries more contaminants.
Tip the snowthrower forward onto its auger
housing and block it so that it cannot fall.
3.
Remove the
back cover.
Max. fill: 26 oz. (0.77 l), type: automotive detergent oil
with an API service classification of SF, SG, SH, SJ,
SL, or higher.
•
•
•
For temperatures above 32°F (0°C), use
SAE 30W.
m-6971
4.
5.
lubricate hex shaft (A).
Move the speed selector lever to Position R2.
For temperatures between 0°F and 32°F (–18°C
to 0°C), use SAE 5W30 or SAE 10W.
Dip your finger in automotive oil and lightly
For air temperatures below 0°F (–18°C), use
SAE 0W30.
6.
7.
8.
Move the speed selector lever to Position 6.
Lubricate the other end of the hex shaft.
Move the speed selector lever forward and
rearward a few times.
Install the back cover and return the snowthrower
to the operating position.
9.
3329-773
Rev A
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38632, Toro Power Max 828LE |
| Model Number | 38632 |
| Model Year | 2004 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 240000001 - 240999999 |
| Product Name | Toro Power Max 828 LE Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Snowthrower, Two Stage Power Max |
| Swath | 28 inch |
| Discharge | Two Stage |
| Engine Manufacturer | Tecumseh |
| Engine Oil Type | 26 oz. (.8l) 5w-30 or 10w / API SH or higher |
| Gearbox Lubricant | 4.5 oz. (133ml) SAE 90 GL5 or higher |
| Engine Motor Model # | HMSK80-155672X |
| Engine Motor Size | 8 hp |
| Engine Motor Type | 4 Cycle CARB2, EPA2 |
| Transmission Speed | 6 Forward/2 Reverse |
| Transmission Type | Friction Disc |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)