Poulan BH 2660 Chainsaw Owners Manual

S  DO NOT cut  down a partially fallen  tree
withyour saw.  Beextremely cautious with
partially fallen  trees  that may  be poorly
supported.  When a tree doesn’t fall com-
pletely,setthesawasideandpulldownthe
tree with a cable winch, block and tackle,
or tractor.
CUTTING A FALLEN TREE
(BUCKING)
Bucking is the term used for cutting a fallen
tree to the desired log size.
WARNING:   Never turn saw upside
down to undercut. The saw cannot be con-
trolled in this position.
Always make your first cut on the compres-
sionsideofthelog.   Thecompressionsideof
the log  is where  the pressure of  the log’s
weight is concentrated.
First cut on compression side of log
WARNING:  Donot  standon thelog
being cut.  Any portion can roll causing loss
of footing and control. Do not stand downhill
of the log being cut.
Second cut
Second cut
IMPORTANT POINTS
S  Cut only one log at a time.
S  Cut shattered wood very carefully; sharp
piecesofwoodcouldbeflungtowardoper-
ator.
S  Use a sawhorse to cut small logs. Never
allow another person to hold the log while
cuttingandnever  holdthelogwith  your leg
or foot.
First cut on compression side of log
S  Do not cut in an  area where logs, limbs,
and roots are tangled such as in a blown
down area. Drag the logs intoa clear area
before cutting by pulling out exposed and
cleared logs first.
TYPES OF CUTTING USED FOR
BUCKING
BUCKING WITHOUT A
SUPPORT
S  Overcut through 1/3 of the diameter of the
log.
S  Roll the log over and finish with a second
overcut.
S  Watch for logs with a compression side to
prevent  the saw  from  pinching.  See il-
lustrations for cutting logs with acompres-
sion side.
WARNING:
If  saw   becomes
pinched or hung in a log, don’t try to force it
out. Youcanlosecontrolofthesawresulting
in injury and/or damage to the saw. Stop the
saw,driveawedgeofplastic   orwoodintothe
cutuntil thesaw  canbe removedeasily.  Re-
startthesawandcarefullyreenterthecut.    To
avoid kickback  and chain damage,  do not
useametalwedge.   Donotattempt  torestart
your saw when it is pinched or hung in a log.
BUCKING USING A LOG OR
SUPPORT STAND
S  Remember your first cut is always on the
compression side of the log.
(Refer to  the illustrations below  for your
first and second cut)
S  Your first  cut  should  extend  1/3  of  the
diameter of the log.
Use a wedge to remove pinched saw
S  Finish with your second cut.
Using a log for support
2
nd Cut
Turn  saw OFF and use a plastic or
wooden wedge to force cut open.
Overcutting beginsonthetopsideofthelog
with the bottom of the saw  against the log.
When overcutting use light downward pres-
sure.
Overcutting
Undercutting
1st Cut
st Cut
1
Undercuttinginvolves cuttingon theunder-
sideofthelogwithtopofsaw     againstthelog.
When undercutting  use light upward  pres-
sure.  Hold saw firmly and maintain control.
The saw will tend to push back toward you.
2
nd Cut
12
Product Specification
CategoriesChainsaw Manuals, Poulan Chainsaw Manuals
Tags
Model Year2005
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 18 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw
Document File TypePDF
Publisherpoulan.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website