authorized
service
dealer
or
call
1.
2.
3.
4.
Loosen 3 screws on cylinder cover.
Remove the cylinder cover.
1--800--554--6723.
Pull off the spark plug boot.
BAR MAINTENANCE
Remove spark plug from cylinder and dis-
card.
If your saw cuts to one side, has to be forced
through the cut, or been run with an improper
amount of bar lubrication it may be necessary
to service your bar. A worn bar will damage
your chain and make cutting difficult.
5.
Replace with Champion RCJ--7Y spark
plug and tighten securely with a 3/4 inch
(19 mm) socket wrench. Spark plug gap
should be 0.025 inch (0.6 mm).
Reinstall the spark plug boot.
6.
7.
After each use, ensure ON/STOP switch is in
theSTOPposition,thencleanallsawdust from
the guide bar and sprocket hole.
Reinstall the cylinder cover and 3 screws.
Tighten securely.
Screws
Cylinder
Cover
To maintain guide bar:
S Move ON/STOP switch to the STOP posi-
Spark
Plug Boot
tion.
S Loosen and remove chain brake nuts and
chain brake. Remove bar and chain from
saw.
Spark
Plug
S Cleantheoilholes andbargrooveaftereach
5
hours of operation.
STORAGE
Remove Sawdust From
Guide Bar Groove
WARNING:
Stop engine and allow
to cool, and secure the unit before storing or
transporting in a vehicle. Store unit and fuel
in an area where fuel vapors cannot reach
sparks or open flames from water heaters,
electric motors or switches, furnaces, etc.
Storeunitwithallguards inplace.Positionso
that any sharp object cannot accidentally
cause injury to passersby. Store the unit out
of reach of children.
Oil Holes
S Burringofguidebar rails is a normalprocess
of rail wear. Remove these burrs with a flat
file.
S When rail top is uneven, use a flat file to re-
store square edges and sides.
S Before storing, drain all fuel from the unit.
Start engine and allow to run until it stops.
S Clean the unit before storing. Pay particu-
lar attention to the air intake area, keeping
it free of debris. Use a mild detergent and
sponge to clean the plastic surfaces.
S Donotstoretheunitorfuelinaclosedarea
where fuel vapors can reach sparks or an
openflamefromhotwater heaters,electric
motors or switches, furnaces, etc.
File Rail Edges
and Sides
Square
Worn Groove
Correct Groove
Replace guide bar when the groove is worn,
theguidebar is bentor cracked,or whenexce-
ss heating or burring of the rails occurs. If re-
placementis necessary,useonlytheguidebar
specified for your saw in the repair parts list or
on the decal located on the chain saw.
S Store in a dry area out of the reach of chil-
dren.
CAUTION:
It is important to prevent gum
deposits from forming in essential fuel system
parts such as the carburetor, fuel filter, fuel
hose, or fuel tank during storage. Alcohol
blended fuels (called gasohol or using ethanol
or methanol) can attract moisture which leads
to fuel mixture separation and formation of
acids during storage. Acidic gas can damage
the engine.
CHAIN SHARPENING
Chain sharpening is a complicated task that
requires special tools. We recommended
you refer chain sharpening to a professional
chain sharpener.
IGNITION TIMING
Ignition timing is fixed and nonadjustable.
NEED ASSISTANCE?
SPARK PLUG
The spark plug should be replaced each
year to ensure the engine starts easier and
runs better.
NEED ASSISTANCE?
Call 1--800--554--6723.
NEED SERVICE PART?
Contact your authorized service dealer.
15
Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
---|---|
Tags | Poulan BH 2660 |
Model Year | 2005 |
Download File |
|
Document Type | Owner's Manual |
Language | English |
Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
Document File Type | |
Publisher | poulan.com |
Wikipedia's Page | Poulan |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)