Poulan Pro PP4620AVHD Chainsaw Owners Manual

4.
5.
6.
Push the choke/fast idle  lever in to the
HALF CHOKE position.
(0.5  mm) thick.  Repairs  on  a chain  brake
shouldbemadeby  anauthorizedservicedeal-
er. Take your unit to  the place of purchase if
purchased from a  servicing dealer, or  to the
nearest authorized master service dealer.
Pull the  starter rope  quickly  with your
right hand until the engine starts.
Allow theenginetorunfor  approximately
30
seconds. Then, squeeze and release
S  This saw is equipped with a chain brake.
The brake is designed to stop the chain if
kickback occurs.
throttletrigger toallow engineto  returnto
idle speed.
S  The
inertia--activated   chain   brake   is
ON/STOP SWITCH
activated if the front hand guard is pushed
forward,  either  manually   (by  hand)  or
automatically (by sudden movement).
S  If  the  brake  is  already  activated,  it  is
disengagedby pullingthefronthandguard
back  toward the  front handle  as  far as
possible.
S  Whencuttingwiththesaw,thechainbrake
must be disengaged.
CHOKE/FAST IDLE LEVER
Disengaged
Engaged
FULL
HALF  OFF
Braking function control
CAUTION:
checked several times daily. The engine must
be running  when performing  this procedure.
This is the only instance when the saw should
be placed on the ground with the engine run-
ning.
Place the saw on firm ground. Grip the rear
handlewithyourrighthandandthefronthan-
dle with your left hand. Apply full throttle by
fully depressing the throttle trigger. Activate
the  chain brake  by turning  your  left wrist
against  the hand  guard  without releasing
your grip around the front handle. The chain
should stop immediately.
STARTING A WARM ENGINE
The  chain  brake   must  be
1.
2.
MoveON/STOP switchtotheONposition.
Pull the  choke/fast  idle lever  out to  the
HALF CHOKE position.
3.
4.
Pull the starter rope quickly with your right
hand until the engine starts.
Squeeze and release the throttle trigger
to allow engine to return to idle speed.
DIFFICULT STARTING (or starting a
flooded engine)
The engine may be flooded if it has not started
after 10 pulls.
Floodedengines canbe clearedof  excess fuel
by following the  warm engine starting proce-
dure  listed  above.   Ensure  the  ON/STOP
switch is in the ON position.
Startingcouldrequiremanypulls   dependingon
how badly unit is flooded. If engine still fails to
start, refer to  TROUBLESHOOTING TABLE
or call 1-800-554-6723.
Inertia activating function control
WARNING:
When performing the
following  procedure,  the  engine must  be
turned off.
Grip therear handlewith your right handand
the front handle with your left hand. Holdthe
chain saw approximately 14(35 cm) above
a stump or other wooden surface. Release
your grip  on the front  handle and  use the
weight of the saw to let the top of the guide
bar  fall  forward  and  contact  the  stump.
When the tip of the  bar hits the stump, the
brake should activate.
CHAIN BRAKE
WARNING:  Ifthebrakebandisworn
too thin it may break when the chain brake is
triggered. With a broken brake band, the chain
brake will not stop the chain. The chain brake
should be replaced by  an authorized service
dealer if any part is worn to less than 0.020
CUTTING METHODS
IMPORTANT POINTS
S  Stop the saw if the chain strikes a foreign
object.  Inspect the saw and repair or re-
place parts as necessary.
S  Keep the chain out of dirt and sand. Even a
small amount of dirt will quickly dull a chain
andthus increasethepossibility  ofkickback.
S  Check chain tension before first use and
after 1 minute of  operation.  See CHAIN
TENSION in the ASSEMBLY section.
S  Cut wood only. Do not cut metal, plastics,
masonry,  non-wood  building   materials,
etc.
10
Product Specification
CategoriesChainsaw Manuals, Poulan Pro Chainsaw Manuals
Tags
Model Year2005
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 18 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandPoulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw
Document File TypePDF
Publisherpoulanpro.com
Wikipedia's PagePoulan
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website