Toro 5 Blade Cutting Unit 03527 03528 Reelmaster 5000 5200 D 5400 D Lawn Mower Operators Manual, 2005

D. Adjusting the Height of Cut
The Turf Compensation Spring also transfers weight
from the front to rear roller. This helps to reduce a
wave pattern in the turf, also known as bobbing.
1.
2.
3.
Rotate the  cutting unit vertical and place  the gauge bar
across front and rear  rollers (Fig. 14).
Important
Make spring adjustments  with cutting unit
Loosen the locknuts  securing the height-of-cut
brackets to each end  of the cutting unit (Fig.  14).
mounted to traction unit  and lowered to shop floor.  Refer
to Traction Unit  Operator’s Manual for mounting
instructions.
Set the head of  the height of cut screw on the  gauge
bar to the desired  height of cut, making this
measurement from the  bar face to the underside  of the
screw head.
1.
Tighten lock nut on  rear of spring rod until the gap  (C)
between rear of spring  bracket and front of washer is
1.25”
(32 mm) (Fig. 15).
4.
Place the bar across  the front and rear rollers and
adjust the tap bolt  until the underside of the  screw
head engages the  bedknife cutting edge (Fig. 14).
“B”
Important
Do step 3 on  each end of the bedknife.
Tighten the height-of-cut  adjustment locknuts on both
ends. Recheck  the adjustment.
“A”
“C”
Note: Same procedure is  used when Front Height of Cut
kit, Part No. 104–8205  is installed on cutting unit.
Figure 15
2.
Tighten hex nuts on front  end of spring rod until the
compressed length (A) of spring  is 6.25 (159 mm)
(Fig. 15).
2
1
Note: As compressed spring length (A)
decreases, weight transfer from front
roller to rear roller increases and
carrier frame/cutting unit rotation angle
(B) decreases.
Note: As gap (C) between spring bracket and
washer increases, cutting unit ground
clearance decreases and carrier
frame/cutting unit rotation angle (B)
increases.
Figure 14
1.
Locknut
2.   Gauge bar
E. Adjusting Turf
Compensation Spring
The Turf Compensation Spring (Fig. 15), connecting
carrier frame to cutting unit, controls the amount of
fore-aft rotation available for the cutting unit
11
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags, , , , , ,
Model Number03527, 03528
Model Year2005
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 16 pages
Document TypeOperator's Manual
LanguageEnglish
Serial Number250000001-250999999
Product NameToro 5-Blade Cutting Unit, Reelmaster 5200-D and 5400-D
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Product TypeAttachment
Product SeriesToro Reelmaster Accessories
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website