OPERATION
HOW TO CLEAR A CLOGGED DISCHARGE CHUTE
WARNING: Hand contact with the rotating im-
peller inside the discharge chute is the most
common cause of injury associated with snow
blowers. NEVER USE YOUR HAND TO CLEAN OUT
THE DISCHARGE CHUTE.
Use a clean-out tool to remove snow from the auger housing.
How To Use The Clean-Out Tool
S
S
Release the auger drive lever.
Remove the ignition key, if equipped. Pull out the safety
key, if equipped.
To Clear The Chute:
S SHUT OFF THE ENGINE!
S
S
Disconnect spark plug wire.
Do not place your hands in the auger or discharge chute.
Use a clean-out tool to remove snow or debris.
S Wait 10 seconds to be sure that the impeller blades
have stopped rotating.
S Always use a clean-out tool, not your hands.
WARNING: Blockage must be cleared only after
shutting off the snow blower and only with a
clean-out tool, not by hand.
SNOW THROWING TIPS
10. After each snow throwing job, allow the engine to run for
a few minutes. The snow and accumulated ice will melt off
the engine.
1.
When the handle is raised, the auger blades will engage
the ground and the snow thrower will move forward. When
the auger drive lever is released, the auger blades will
stop. If the blades do not stop, see “How To Adjust The Au-
ger Control Cable” in the Service And Adjustment section.
11.
12.
Clean the snow thrower after each use.
Remove ice, snow and debris from the entire snow throw-
er. Flush with water to remove all salt or other chemicals.
Wipe snow thrower dry.
2.
3.
Most efficient snow throwing is accomplished when the
snow is removed immediately after if falls.
DRY AND AVERAGE SNOW
For complete snow removal, slightly overlap each pre-
vious path.
1. Snow up to eight inches deep can be removed rapidly and
easily by walking at a moderate rate. For snow or drifts of
a greater depth,slow your pace to allow the discharge
chute to dispose of the snow as rapidly as the auger re-
ceives the snow.
4.
5.
Whenever possible, discharge the snow down wind.
The distance the snow will be discharged can be adjusted
by moving the discharge chute deflector. Raise the deflec-
tor for more distance or lower the deflector for less dis-
tance.
2.
Plan to have the snow discharged in the direction the wind
is blowing.
6.
7.
8.
9.
In windy conditions, lower the chute deflector to direct the
discharged snow close to the ground where it is less likely
to blow into unwanted areas.
WET PACKED SNOW
Move slowly into wet, packed snow. If the wet, packed snow
causes the auger to slow down or the discharge chute begins
to clog, back off and begin a series of short back and forth jabs
into the snow. These short back and forth jabs, four to six inch-
es, will “belch” the snow from the chute.
For safety and to prevent damage to the snow thrower,
keep the area to be cleared free of stones, toys and other
foreign objects.
Do not use the auger propelling feature when clearing
gravel or crushed rock driveways. Move the handle down
to slightly raise the auger.
SNOW BANKS AND DRIFTS
The forward speed of the snow thrower is dependent on
the depth and weight of the snow. Experience will estab-
lish the most effective method of using the snow thrower
under different conditions.
In snow of greater depth than the unit, use the same “jabbing”
technique described above. Turn the discharge chute away
from the snow bank. More time will be required to remove snow
of this type than level snow.
1740274
17
| Categories | Husqvarna Snow Blower Manuals, Snow Blower Manuals |
|---|---|
| Tags | Husqvarna 521SSE, Husqvarna 521SSR |
| Model Year | 2006, 2007, 2008 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Husqvarna, Snow Blower |
| Document File Type | |
| Publisher | husqvarna.com |
| Wikipedia's Page | Husqvarna |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)