slopingterrain. Useaplumb or level tode-
termine the direction of tree lean.
CUTTING METHODS
S Weight and branches on one side.
S Surrounding trees and obstacles.
Look for decay and rot. If thetrunk is rotted,
IMPORTANT POINTS
it can snap and fall toward the
operator.
S Check chain tension before first use and
after 1 minute of operation. See CHAIN
TENSION in the ASSEMBLY section.
S Cut wood only. Do not cut metal, plastics,
masonry, non-wood building materials, etc.
S Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or re-
place parts as necessary.
Check for broken or dead branches which
can fall on you while cutting.
Make sure there is enough room for the tree
to fall. Maintain a distance of 2-1/2 tree
lengths from the nearest person or other ob-
jects. Enginenoisecan drownout awarning
call. Remove dirt, stones, loose bark, nails,
staples, and wire from the tree where cuts
are to be made. Plan a clear retreat path to
the rear and diagonal to the line of fall.
S Keep the chain out of dirt and sand. Even a
small amount of dirt will quickly dull a chain
andthus increasethepossibility ofkickback.
S Practice cutting a few small logs using the
following techniques to get the“feel” ofus-
ing your saw before you begin a major
sawing operation.
Plan a clear retreat path
S
Squeeze the throttle trigger and allow
the engine to reach full speed before
cutting.
Begin cutting with the saw frame
against the log.
Direction of Fall
45_
S
S
S
Keep the engine at full speed the entire
time you are cutting.
FELLING LARGE TREES
Allowthechaintocutforyou.Exertonly
light downward pressure. If you force
thecut,damagetothebar,chain,oren-
gine can result.
Release the throttle trigger as soon as
the cut is completed, allowing the en-
gine to idle. If you run the saw at full
throttlewithoutacuttingload,unneces-
sary wear can occur to the chain, bar,
and engine.
Toavoidlosingcontrolwhencutiscom-
plete,donotputpressureonsaw atend
of cut.
(6 inches (15 cm) in diameter or larger)
The notch method is used to fell large trees.
A notchis cutonthesideofthetreeinthede-
sired direction of fall. After a felling cut is
made on the opposite side of tree, the tree
will tend to fall into the notch.
S
S
NOTE:
If the tree has large buttress roots,
removethembeforemakingthenotch. Ifus-
ing saw to remove buttress roots, keep saw
chainfromcontactinggroundtopreventdull-
ing of the chain.
NOTCH CUT AND FELLING THE
TREE
S Stop the engine before setting the saw
down after cutting.
TREE FELLING TECHNIQUES
S
Make notch cut by cutting the top of the
notch first. Cut through 1/3 of the diameter
ofthetree.Nextcompletethenotchbycut-
ting the bottom of the notch. See illustra-
tion. Once the notch is cut remove the
notch of wood from the tree.
WARNING:
Check for broken or
dead branches which can fall while cutting
causingserious injury. Donotcutnearbuild-
ings or electricalwires ifyou donot know the
directionoftreefall,norcutatnightsinceyou
will not be ale to see well, nor during bad
weather suchas rain, snow,or strongwinds,
etc. If the tree makes contact with any utility
line, the utility company should be notified
immediately.
S Carefullyplanyour sawingoperationinad-
vance.
S Cleartheworkarea. Youneedacleararea
allaroundthetreeso youcan havesecure
footing.
Final (felling) cut here, 2 inches
(5 cm) above center of notch.
First cut
Notch
Hinge
Second cut
S The chain saw operator should keep on
the uphill side of the terrain as the tree is
likelytorollor slidedownhillafteritisfelled.
S Study the natural conditions that can cause
the tree to fall in a particular direction.
Natural conditions that can cause a tree to
fall in a particular direction include:
S The wind direction and speed.
S The lean of the tree. The lean of a tree
might not be apparent due to uneven or
S After removing the wood from the notch,
make the felling cut on the opposite side of
thenotch.Thisisdonebymakingacutabout
two inches (5 cm) higher than the center of
thenotch.Thiswillleaveenoughuncutwood
between the felling cut and the notch to form
a hinge. This hinge will helpprevent thetree
from falling in the wrong direction.
11
| Categories | Chainsaw Manuals, Poulan Chainsaw Manuals |
|---|---|
| Tags | Poulan 1950, Poulan 1975, Poulan 2050, Poulan 2050WT, Poulan 2055, Poulan 2075, Poulan 2150, Poulan 2150PR, Poulan 2155, Poulan 2175, Poulan 2350, Poulan 2375 |
| Model Year | 2006 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan. Poulan US phone support. Wheeled (Mowers, Tractors, Tillers): 1-800-849-1297 Handheld (Chainsaws, Trimmers): 1-800-554-6723 , Chainsaw |
| Document File Type | |
| Publisher | poulan.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)