S Wash the filter in soap and water. Air dry
completely before reinstalling.
S Replace parts.
After each use, ensure ON/STOP switch is
in the STOP position, then clean all sawdust
from the guide bar and sprocket hole.
To maintain guide bar:
S Move ON/STOP switch to the STOP posi-
tion.
S Loosen and remove chain brake nuts and
chain brake. Remove bar and chain from
saw.
S Clean the oil holes and bar groove after
each 5 hours of operation.
Remove Sawdust From
Guide Bar Groove
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
Sprocket Hole
Oil Holes
As the unit is used, carbon deposits build up
on the muffler and spark arresting screen,
and must be removedto avoidcreating afire
hazard or affecting engine performance.
Replacethespark arrestingscreen ifbreaks
occur.
S Add lubricant to sprocket hole after each
use.
Spark Arrestor
Screen
S Burring of guide bar rails is a normal pro-
cessofrailwear. Removetheseburrswith
a flat file.
S Whenrailtopis uneven,useaflatfiletore-
store square edges and sides.
File Rail Edges
and Sides
Square
Worn Groove
Correct Groove
CLEANING THE SPARK ARREST-
ING SCREEN
Clean every 25 hours of operation or annually,
whichever comes first.
S Loosen and remove the muffler cover
screws.
S Removethemuffler cover(cover snapsoff
muffler body).
Replace guide bar when the groove is worn,
the guide bar is bent or cracked, or when
excess heating or burring ofthe rails occurs.
If replacement is necessary, use only the
guide bar specified for your saw in the repair
parts list or on thedecal locatedon thechain
saw.
S Remove muffler diffuser and spark arrest-
ing screen assembly. Notice the orienta-
tion of parts for reassembly.
S Clean the spark arresting screen with a
wire brush. Replace screen if breaks are
found.
CHAIN SHARPENING
Chain sharpening is a complicated task that
requires special tools. We recommended
you refer chain sharpening to a professional
chain sharpener.
S Replace any broken or cracked muffler
parts.
IGNITION TIMING
Ignition timing is fixed and nonadjustable.
S Reinstall diffuser and
spark
arresting
screen assembly with holes facing up and
toward muffler cover.
SPARK PLUG
The spark plug should be replaced each
year to ensure the engine starts easier and
runs better.
S Reinstall muffler cover and screws. Tight-
en securely.
CARBURETOR ADJUSTMENTS
S
Loosenandremovethescrews on thecyl-
inder cover.
Your carburetor is equipped with limiter
caps.
Carburetor adjustment is a compli-
S
S
S
Remove the cylinder cover.
Pull off the spark plug boot.
Remove spark plug from cylinder and dis-
card.
cated task. We recommend that you take
your unit to an authorized service dealer.
Damagewilloccur ifyouturntheneedlesbe-
yond the limiter stops.
S Replace with Champion RCJ--7Y spark
plug and tighten securely with a 3/4 inch
socket wrench. Spark plug gap should be
0.025 inches.
S Reinstall the spark plug boot.
S Reinstall the cylinder cover and screws.
Tighten securely.
BAR MAINTENANCE
If your saw cuts to oneside, has to beforced
throughthecut,or beenrunwithanimproper
amount of bar lubrication it may be neces-
sary toserviceyour bar.A wornbar willdam-
age your chain and make cutting difficult.
14
| Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
|---|---|
| Tags | Poulan Pro 330, Poulan Pro 380 |
| Model Year | 2006 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
| Document File Type | |
| Publisher | poulanpro.com |
| Wikipedia's Page | Poulan |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
Tried to download poulan 330 china’s manual. Would not work. Need to see carburetor. Where to put gasket