Note: Moving the Z-fitting higher decreases the
gap between the control bar and the handle; moving
it lower increases the gap.
3.
4.
Hook the spring to the adjuster link and slide the
spring cover over the adjuster link.
Check the adjustment; refer to Checking the Control
Cable.
Note: After extended use, the drive belt may wear
and lose its proper belt tension. If the drive belt
slips (continuously squeals) under a heavy load,
disconnect the spring from the adjustor link and
move the upper end of the spring to the hole that
is further from the pivot point in the control bar
(Figure 22). Then connect the spring to the adjustor
link and adjust the control cable.
Figure 23
1.
Wear indicator hole
Servicing the Spark Plug
Service Interval: Yearly—Service the spark plug and
replace it if necessary.
Use a NGK BPMR4A spark plug or equivalent.
1.
2.
3.
Stop the engine and wait for all moving parts to stop.
Rotate the discharge chute so that it faces forward.
Remove the discharge chute, the discharge chute
handle, and the chute seal by removing the 3 large
screws and one small screw (Figure 24).
Figure 22
1.
Remove the upper end of
spring from this hole
3.
4.
Pivot point
2.
Insert the upper end of
spring into this hole
Upper end of spring
Note: The belt may slip (squeal) in wet conditions;
to dry out the drive system, start the rotor and run
it without a load for 30 seconds.
Inspecting the Rotor Blades
Figure 24
Service Interval: Yearly—Inspect the rotor blades and
have an Authorized Service Dealer
replace the rotor blades and scraper if
necessary.
1.
Discharge chute handle
Large screw (3)
Chute seal
4.
5.
Discharge chute
Small screw
2.
3.
Before each session, inspect the rotor blades for wear.
When a rotor blade edge has worn down to the wear
indicator hole, have an Authorized Service Dealer
replace the rotor blades and the scraper (Figure 23).
4.
Remove the 4 screws that secure the shroud
(Figure 24).
5. Remove the fuel tank cap.
12
| Categories | Snow Blower Manuals, Toro Snow Blower |
|---|---|
| Tags | Toro 38581, Toro 38582 |
| Model Number | 38581, 38582 |
| Model Year | 2008 |
| Download File |
|
| Document Type | Operator's Manual |
| Language | English |
| Serial Number | 280000001 - 280999999 |
| Product Name | Toro Power Clear Snowthrower |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower |
| Product Type | Snowthrower |
| Product Series | Power Clear, Snowthrower |
| Swath | 21 inch |
| Discharge | Single Stage |
| Engine Manufacturer | Briggs & Stratton |
| Engine Oil Type | Toro 2 cycle / NMMA-TCW3 |
| Engine Motor Model # | 0842330199E8 |
| Engine Motor Size | 141cc |
| Engine Motor Type | 2 Cycle EPA2 |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro Power Clear 38581 38582 Snow Blower Operators Manual 2008 5.0 out of 5.0 based on 1 product reviews. Very Easy To Start In The Worst Conditions. Have Had This Machine For 7 Years. A Real Work Horse. Removing Snow With This Machine Is A Walk IntThe Park. Love it.