S After removingthe woodfrom thenotch,
makethe fellingcut onthe oppositeside
of the notch. This is done by making a
cut about two inches higher than the
center of the notch. This will leave
enough uncut wood between the felling
cut and the notch to form a hinge. This
hinge will help prevent the tree from fal-
ling in the wrong direction.
BUCKING TECHNIQUES
WARNING:
If
saw
becomes
pinchedorhunginalog,don’ttrytoforceit
out.Youcanlosecontrolofthe sawresult-
ing in injury and/or damage to the saw.
Stop the saw, drive a wedge of plastic or
wood into the cut until the saw can be re-
moved easily. Restart the saw and care-
fully reenter the cut. Do not use a metal
wedge.Do notattemptto restart yoursaw
when it is pinched or hung in a log.
Hinge holds tree on stump and
helps control fall.
Use a wedge to remove pinched saw
Opening
of felling
cut
Closing of
notch
Turn saw OFF and use a plastic or
wooden wedge to force cut open.
NOTE: Before felling cut is complete,
use wedges to open the cut when
necessary to control the direction of fall.
To avoid kickback and chain damage,
use wood or plastic wedges, but never
steel or iron wedges.
Overcutting begins on the top side ofthe
log with the bottom of the saw against the
log. When overcuttinguse lightdownward
pressure.
Overcutting
Undercutting
S Be alert to signs that the tree is ready to
fall: cracking sounds, widening of the
felling cut, or movement in the upper
branches.
S As tree starts to fall, stop saw, put it
down, and get away quickly on your
planned retreat path.
Undercutting involves cutting on the un-
derside of the log with top of saw against
the log. When undercutting use light up-
ward pressure. Hold saw firmly and main-
tain control. The saw will tend to push
back toward you.
S DONOTuseyoursawtocutdown apar-
tially fallen tree. Be extremely cautious
with partially fallen trees that may be
poorly supported. When a tree doesn’t
fall completely, set saw aside and pull
down tree with a cable winch, block and
tackle, or tractor.
WARNING: Neverturn sawupside
down to undercut. The saw cannot be
controlled in this position.
CUTTING A FALLEN TREE
Always make your first cut on the com-
pressions side of the log. The compres-
sion side of the log is where the pressure
of the log’s weight is concentrated.
First cut on compression side of log
(BUCKING)
Bucking is the term used for cutting a fall-
en tree to the desired log size.
WARNING: Do not stand on the
log being cut. Any portion can roll caus-
ing loss of footing and control. Do not
stand downhill of the log being cut.
IMPORTANT POINTS
S Cut only one log at a time.
S Cut shattered wood very carefully;
sharp pieces of wood could be flung to-
ward operator.
Second cut
Second cut
S Useasawhorsetocutsmall logs.Never
allow another person to hold the log
while cutting and never hold the log with
your leg or foot.
S Do not cut in an area where logs, limbs,
and roots are tangled. Drag logs into a
clear area before cuttingthem bypulling
out exposed and cleared logs first.
First cut on compression side of log
BUCKING WITHOUT A SUPPORT
S Overcut through 1/3 of the diameter of
the log.
S Roll the log over and finish with a sec-
ond overcut.
10
Categories | Chainsaw Manuals, Poulan Pro Chainsaw Manuals |
---|---|
Tags | Poulan Pro PP400E |
Model Year | 2010 |
Download File |
|
Document Type | Owner's Manual |
Language | English |
Product Brand | Poulan Pro. Poulan Pro US phone support. Wheeled (Mowers, Tractors, Tillers, Snow Throwers): 1-800-849-1297, Handheld (Chainsaws, Trimmers, Blowers, Edgers): 1-800-554-6723, Chainsaw |
Document File Type | |
Publisher | poulanpro.com |
Wikipedia's Page | Poulan |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)